User manual SAMSUNG DSB-A100

[. . . ] DSB-A100F Instructions for use GB MF68-00312A REV. 1. 0 DIGITAL SATELLITE RECEIVER DIGITAL SATELLITE RECEIVER DSB-A100F SAFETY INSTRUCTIONS This STB has been manufactured to satisfy international safety standards. Please read the following recommended safety precautions carefully. MAINS SUPPLY: OVERLOADING: LIQUIDS: CLEANING: AC 100-240V~, 50/60Hz Do not overload wall outlets, extension cords or adapters as this can result in fire or electrical shock. Before cleaning, disconnect the STB from the wall socket. [. . . ] Enter the PIN Code. 1. 2 Positioner Setting If you have a DiSEqC 1. 2 motorized system which is fully compatible with DiSEqC1. 2, then you can take advantage of the DiSEqC 1. 2 functions available. If you have not entered your own PIN Code then the PIN Code 0000 applies, which was set at the factory. Select Satellite. Select any transponder from above satellites and check out the Frequency, Symbol Rate, FEC and Polarity. In case problems arise, ask your dealer. Sometimes this transponder may not exist due to broadcasting. It is better to select main transponder among them for the desired satellite. Select from Menu Mode: Enables control of basic positioner function recommended for beginners. General user uses "User" mode. "User" mode : "Installer" mode : This is used to search for the position of a satellite manually. GB-16 D I G I T A L S A T E L L I T E R E C E I V E R GB-17 DSB-A100F 1. 2. 1 User Mode DSB-A100F OPERATING THE RECEIVER OPERATING THE RECEIVER 1. 3 Solarsat Setting This menu is only for the Solarsat antenna. When you press this menu, you will get this message, "This menu is only for the Solarsat antenna. If you have one-press OK, otherwise-press EXIT. " You can set the value according to your location. To set the Value of Date and Time, use the PG+/PG- keys to change the value. Use the / keys to move each filed. Select Driving Mode: You have an option to choose the positioner's movement type: Continuous, Step or Time. Position the antenna with north, south, east and west and use the / / / key to drive motor. key drives to west, key drives to east, key drives to north and key drives to south. If you finished driving of motor, select "Store current Position. " and press OK key, to reset new driving motor. Note : The level indicated in the "Signal Status" is only for reference. The signal quality may be adequate even though the level indicated is not maximum. GB 1. 4 Auto Scanning The sub menu "Auto Scanning" will enable download the channels automatically from the preprogrammed satellites. To download channels automatically: You can select All/Off/Only Free option mode with the the / keys in each satellite, which can be displayed more by the PG+/PG- keys . Off : No Scan All : Scan all the channels Only Free : Scan free channels Go to Stored Position. When the stored position is reached then screen displays "Stop", you can now continue with the further operations. Select the Calculate Sat Positions to recalculate the satellite position and OK key. 1. 2. 2 Installer Mode After checking the positioner's state, installer should use this menu. He should set the "Disable Limits" before using User mode. Select the Drive Motor West/East and use the / keys to drive motor. key drives to west and key drives to east. Select "Enable Limit", in order to enable "Set Limit". Select "Disable Limit", in order to disable "Set Limit". Select "Reset Positioner" and OK key to reset positioner. Press OK key. Auto Scanning menu will be displayed. [. . . ] Press `OK' to start channel data copy If you have to contact your service provider or a service center they might ask for information available from this menu. Place the cursor on this sub menu and press the OK key. The following will be the on-screen display. Note : If you forgot PIN Code, press `0' key four times. [. . . ]