User manual SAMSUNG DSR-9500

[. . . ] DSR 9500A FTA, CI, EM VIA, VIA CI Instructions for use "REV 1. 0" GB DIGITAL SATELLITE RECEIVER MF68-00247A DSR 9500A FTA, CI, EM VIA, VIA CI SAFETY INSTRUCTIONS This STB has been manufactured to satisfy international safety standards. Please read the following recommended safety precautions carefully. MAINS SUPPLY: OVERLOADING: LIQUIDS: CLEANING: AC 100-240V ~, 50/60Hz Do not overload wall outlets, extension cords or adapters as this can result in fire or electrical shock. Before cleaning, disconnect the STB from the wall socket. Use a cloth lightly dampened with water(no solvents) to clean the exterior. [. . . ] Teletext OSD When the current broadcasting program provides Teletext OSD, press the Green ( ) key twice to see the current Teletext OSD list. To change the Teletext OSD: q q Main Menu After installing your antenna system and DSR 9500A with appropriate connectors. q q Plug in the AC main power and switch on the receiver. Press MENU key to bring up the main menu. The LED display will show "MENU". Use the / keys to select a Teletext OSD you want. Press the key and then the Teletext OSD you want is displayed on the screen. The following on screen display will appear: The sub menu topics will be displayed. For the sub-menus 1, 2 and 3 you need the PIN code. q 9. Teletext VBI When the current broadcasting program provides Teletext VBI, press the Green ( ) key three times to see the current Teletext VBI list. To change the Teletext VBI: q q You must follow the help message at the bottom of the screen! GB Before you begin with the "Installation" menu, you should check in the 4th menu "System Setup" whether all the information there is applicable for you. Use the / keys to select a Teletext VBI you want. Press the key and then the Teletext VBI you want is displayed on the screen. 1. Installation The menu provides settings for customizing, adding new services and displaying the status of the receiver. q q Select "Installation" in the main menu mode to select the sub menu. Enter the PIN code. If you have not entered your own PIN code then the PIN code 0000 applies, which was set at the factory. GB-14 D I G I T A L S A T E L L I T E R E C E I V E R GB-15 DSR 9500A FTA, CI, EM VIA, VIA CI DSR 9500A FTA, CI, EM VIA, VIA CI OPERATING THE RECEIVER OPERATING THE RECEIVER 1. 1 LNB Setting You can select the satellite and LNB setting conditions to execute channel search and you can alter the settings for 22kHz tone. The parameters set in this menu are needed for programming the channels for the "Auto scanning" and "Manual scanning". The necessary information can be found at your antenna and LNB brochures, or you can ask your dealer. q q q q q Select from Menu Mode: Enables control of basic positioner function recommended for beginners. General user uses "User" mode. Complete control of the positioner's full functions recommended for installers and professional users. "User" mode : "Installer" mode : 1. 2. 1 User Mode q Select LNB power supply "On". Select the DiSEqC Mode (Off, DiSEqC A, DiSEqC B, DiSEqC C, DiSEqC D, Tone Burst A, Tone Burst B) q If you are using a Positioner, select this option. ("Yes" or "No") q 22KHz: In case you are using a dual LNB or two antennas connected to a 22KHz tone switch box, with the 22 KHz tone switch ("On", "Off" or "Auto") you can switch between both LNB or antennas. Select Driving Mode: You have an option to choose the positioner's movement type: Continuous, Step or Time. Position the antenna with north, south, east and west and use the / , / key to drive motor. key drives to west, key drives to east, key drives to north and key drives to south. If you finished driving of motor, select "Store current Position. " and press key, to reset new driving motor. GB 1. 2 Positioner Setting If you have a DiSEqC 1. 2 motorized system, then you can take advantage of the DiSEqC 1. 2 functions available. q q Note : The level indicated in the "Signal Status" is only for reference. The signal quality may be adequate even though the level indicated is not maximum. q Go to Stored Position. Select Satellite. Select any transponder from above satellites and check out the Frequency, Symbol Rate, FEC and Polarity. When the stored position is reached then screen displays "Stop", you can now continue with the further operations. q Select the Calculate Sat Positions to recalculate the satellite position and key. In case problems arise, ask your dealer. GB-16 D I G I T A L S A T E L L I T E R E C E I V E R GB-17 DSR 9500A FTA, CI, EM VIA, VIA CI DSR 9500A FTA, CI, EM VIA, VIA CI OPERATING THE RECEIVER OPERATING THE RECEIVER 1. 2. 2 Installer Mode After checking the positioner's state, installer should use this menu. [. . . ] Change Parental Rating: Change the setting for the family filter, if necessary. Note : This service is not offered by all channels. Change Lock indicator: You can change the lock status of the Viaccess Smartcard. Issuer Information: Here you can call up all information stored on the Smartcard by the publisher. [. . . ]