User manual SAMSUNG DTB-B360

[. . . ] We designed it with easy-to-use on-screen menus and closed captioning capabilities, making it one of the best products in its class. We are proud to offer you a product that will provide convenient, dependable service and enjoyment for years to come. Warning!Important Safety Instructions · Use only a grounded or polarized outlet. For your safety, this product is equipped with a polarized alternating current line plug having one blade wider than the other. [. . . ] Use the / , PG+/PG- keys to select a favorite group or a channel that you want. 6. 2 Service Alphabetical Press EPG key while you are viewing a program. Press the YELLOW(ALT) key on the remote control unit to select the Alphabetical list. Press the YELLOW(ALT) key to switch between alphabet list and channel list. Use the / , PG+/PG- keys to select a Alphabetical group or a channel that you want. This function is displayed on the screen by using only time. You will see "EPG" in the LED display of the receiver. GREEN(TEXT) YELLOW(ALT) BLUE(AUDIO) RED( key: Green key is for moving back to the previous date. key: Yellow key is for moving to the next coming date. key can be used for page up, if there is more information than one page. i ) key can be used for page down, if there is more information than one page. 2 key: 30 minutes 3 key: 15 minutes Time interval can be adjusted by press keys as followings on EPG screen: 6. 3 Service Provider 1 key: 1 hour and 30 minutes Press the BLUE(AUDIO) key on the remote control unit to select the Provider list. Press the BLUE(AUDIO) key to switch between Provider list and channel list. Use the / , PG+/PG- keys to select a Provider group or a channel that you want. With the TV/RADIO or FAV key you can browse among the various programs lists. Select the channel by pressing / , PG+/PG- keys and press OK key to watch this channel. Current event can be returned by pressing LAST key during moving events on this channel. When the TIMER key on the remote control is pressed in the EPG screen, if the current channel involves an event, timer is set immediately and the set timer is indicated on the EPG screen. The parameters set in this menu are needed for programming the channels for the "Auto scanning" and "Manual scanning". The necessary information can be found at your antenna and LNB brochures, or you can ask your dealer. Select the DiSEqC Mode (Off, DiSEqC A, DiSEqC B, DiSEqC C, DiSEqC D, Tone Burst A, Tone Burst B) Select the switch 0/12V ("0V" or "12V") If you are using a Positioner, select Positioner DiSEqC1. 2 ("Yes" or "No") 22KHz: In case you are using a dual LNB or two antennas connected to a 22KHz tone switch box, with the 22 KHz tone switch ("On", "Off" or "Auto") you can switch between both LNB or antennas. 0/12V: When you use two LNBs or antennas is switched to 0/12V, select what LNB and antenna are used enable or disable. 0/12V terminal is located on the rear of STB. Select Driving Mode: You have an option to choose the positioner's movement type: Continuous, Step or Time. Select Positioner Slot: When a Satellite position is set with the positioner which doesn't have enough slots and the default slot number in this menu is bigger than a number of slots in a positioner, Positioner slot in menu can be changed and fit to the number of slot in a positioner for a Satellite. Position the antenna with north, south, east and west and use the / / / key to drive motor. key drives to west, key drives to east, key drives to north and key drives to south. If you finished driving of motor, select "Store current Position. " and press OK key, to reset new driving motor. The level indicated in the "Signal Status" is only for reference. The signal quality may be adequate even though the level indicated is not maximum. Note : Go to Stored Position. When the stored position is reached then screen displays "Stop", you can now continue with the further operations. 1. 2 Positioner Setting If you have a DiSEqC 1. 2 motorized system which is fully compatible with DiSEqC1. 2, then you can take advantage of the DiSEqC 1. 2 functions available. Select the Calculate Sat Positions to recalculate the satellite position and OK key. 1. 2. 2 Installer Mode After checking the positioner's state, installer should use this menu. [. . . ] The local time will be changed according to your location. GMT is referred to the standard time of Greenwich by broadcasting signal. 2) Timer 15 timers are supported including timer(s) from EPG. Select the timer number on `Timer' using / keys from 1 to 15. Press the / keys to choose event repetition you want to reserve : Daily, Every Sunday, Every Monday, Every Tuesday, Every Wednesday, Every Thursday, Every Friday, Every Saturday, Once. If the timer is set from EPG screen, EPG is displayed on `Event Repetition'. [. . . ]