User manual SAMSUNG DVD-R121

[. . . ] Instruction Manual DVD-R121 AK68-00700A-00 Getting Started Warning IMPORTANT NOTE The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug. If it requires replacing, a fuse approved to BS1362 of the same rating must be used. Never use the plug with the fuse cover omitted if the cover is detachable. [. . . ] 2 hours) - LP (low quality) : Select when a long recording time is required. (Approx. 4 hours) - EP (extended) : Select when a longer recording time is required. (Approx. 6 hours or 8 hours) unit in 1 With thebutton. Stop mode, press the TIMER DVD-RAM(VR) Disc Navigation Playlist Disc manager Programme Setup G-Code Timer Record G-Code Extended : Off Programme MOVE OK RETURN EXIT Using the MENU button. q q Recording q With the unit in Stop mode, press the MENU button. buttons to select Programme, then press the OK or button. buttons to select Timer Record. 2 Press the OK or button. · The Timer Recording screen is displayed. NOTE s DVD-RAM(VR) Scheduled Record List Recordable Time 02:12 SP No. Source Date Start End Mode Edit - 01 -- -- -- - -- No. 01 --:---:-Source Date Start End Mode When you are recording at EP mode on a DVD-RW(V)/R disc, it may not record the full 6 or 8 hours because the unit uses the VBR(Variable Bit Rate) ENCODING system. For example, if you record a program with a lot of action, it uses a higher bit rate which in turn consumes more disc memory. PR 01 01/JAN(SAT) 12 : 00 14 : 00 SP Recordable Time 02:12 SP MOVE OK RETURN EXIT 3 Set timer recording option. · Fill the input items using the arrow buttons and number buttons. oe : Moves to the previous/next item, . . . , 0~9 : Sets a value. English -43 4 Press the OK button. q will appear on the front panel. It means that a timer recording is registered. If the timer settings overlap The programmes are recorded in order of priority. If timer recording is set for the first programme and then again for the second programme and both programmes overlap, the following message will appear on the screen: "This setting is identical with 1"The message shows that the first programme has priority. After recording of the first program is complete, the second program starts being recorded. To exit without saving the current setting Press the MENU button. To return to the previous menu Press the RETURN button if you don't want to set a timer recording. Editing the Scheduled Record List Follow these directions to edit the timer record list. unit in 1 With thebutton. Stop mode, press the TIMER DVD-RAM(VR) Disc Navigation Playlist G-Code Timer Record G-Code Extended : Off Programme 5 Turn the power off to finish the Timer Recording setting. Timer Recording will not work when the power is on. q Disc manager Programme Setup will blink if disc is not inserted. MOVE OK RETURN EXIT s Recording NOTE The timer recording time may differ from the set time depending on disc status and overall timer recording status (for example, recording times overlapping, or when the previous recording ends within 2 minutes before the start time of the next recording. ) You can make the Timer Recording up to 12 programmes. Using the MENU button. q q q With the unit in Stop mode mode, press the MENU button. buttons to select Programme, then press the OK or button. buttons to select Timer Record. s 2 Press the OK or button. Press the RETURN button 3 Timer Recording screen. to close the DVD-RAM(VR) Scheduled Record List Recordable Time 02:12 SP No. Source Date Start End Mode Edit - Flexible Recording (for Timer recording only) 01 -- -- -- - -- No. 01 --:---:-Source Date Start End Mode PR 01 01/JAN(SAT) 12 : 00 14 : 00 SP Recordable Time 02:12 SP MOVE OK RETURN EXIT In FR mode, the most suitable record mode is adjusted automatically, according to remaining time on the disc and length of the timer recording. [. . . ] (See pages 5, 48. ) The angle operation is available only when the disc contains images captured from different angles. Checkpoint 2 Checkpoint 3 The selected audio and/or subtitle language is not played. icon appears on the screen. Checkpoint 1 Checkpoint 1 You cannot use this operation or function due to one of the following reasons: (1) Your DVD disc restricts it. (2) Your DVD disc does not support this feature (for example: angles) (3) The feature is not available at the moment. (4) You've requested a title, chapter, or scan time that is out of range. Audio and subtitle languages are disc-specific. Only the sound and subtitle languages contained on the DVD disc are available and displayed in the disc menu. Play mode settings are different from the settings configured in the Settings menu. Checkpoint 1 The disc does not support all selected functions. [. . . ]