User manual SAMSUNG FH070EAM1C

[. . . ] Should this happen, switch off the breaker used for your air conditioner and contact your installation specialist. x Make sure that the unit is correctly ventilated at all times: Do not place clothing or other materials over it. x If the wireless remote control will not be used for a long time, remove the batteries. (If applicable) x When using a wireless remote control, the distance should not be more than 7 meters from the air conditioner. [. . . ] However, be careful when you wash the surface of the heat exchanger because it is very sharp. Disconnect all remote electric power supplies before cleaning. E-5 ENGLISH Wireless Remote Controller-Buttons and Display To use the wireless remote controller, refer to an appropriate manual. Operating mode Temperature setting Mode selection button Temperature adjustment buttons Filter Reset button Fan speed Air flow direction On Timer setting Off Timer setting Battery discharge indicator Fan speed adjustment button Swing button On Timer button Off Timer button On/Off & Timer Set/Cancel button Note x After cleaning the air filter, press the button. E-6 Wired Remote Controller-Buttons and Display ENGLISH Temperature setting Fan speed Air flow direction Filter Sign indicator On/Off button Temperature adjustment buttons On Timer button Timer Set/Cancel button Test button On/Off indicator Fan speed adjustment button Swing button (Not operated) Filter Reset button E-7 The wired remote controller is an optional accessory and it is installed on the wall. To use the wired remote controller, refer to an appropriate manual. Operating mode Removing frost indicator Centralized controller indicator (In case of installing the Centralized controller) Communication error indicator On Timer setting Off Timer setting Test indicator Mode selection button Note x The button is for your installation specialist. x After cleaning the air filter, press the button. Then the wired remote controller will display the FILTER SIGN indicator when the time to clean the air filter; refer to page 13. Centralized Controller The centralized controller is an optional accessory and it is installed on the wall. To use the centralized controller, refer to an appropriate manual. Front View Operating lamp All On button All Off button On/Off indicators On/Off buttons Index Note x The operating lamp comes on even when only one air conditioner connected to the centralized controller is operating. Side View Operating Mode Switch COOL AUTO HEAT Note x Choose the appropriate operating mode with the Operating Mode Switch that enables the user to choose between the Cool/Auto/Heat mode. E-8 Function Controller ENGLISH Temperature setting Fan speed Air flow direction Test indicator Temperature adjustment buttons Indoor unit selection button Filter Sign indicator On/Off & Timer Set/Cancel button On/Off indicator Fan speed adjustment button Swing button Test button Filter Reset button E-9 The function controller is an optional accessory and it is installed on the wall. The function controller is an additional controller which is used with the centralized controller. To use the function controller, refer to an appropriate manual. Operating mode Removing frost indicator Centralized controller indicator Communication error indicator Room number display Mode selection button Note x The button is for your installation specialist. x After cleaning the air filter, press the button. Then the wired remote controller will display the FILTER SIGN indicator when the time to clean the air filter. Adjusting the Air Flow Direction There are two sets of inner air flow blades. Just as the outer air flow blade can be adjusted vertically, the inner blades can be adjusted horizontally. Adjust each set of inner blades to the required position, by pushing or pulling them sideways. E-10 Operating Recommendations ENGLISH Here are a few recommendations that you should follow when operating your air conditioner. Topic Heating performances Recommendation The heat pump function of the air conditioner absorbs heat from outside air and brings it indoors. As the temperature of the outside air drops, the heating performance of air conditioner will decrease. If you find that the room is not warm enough, using an additional heating appliance is recommended. When outside temperature is low but humidity is high, frost may form on the outdoor unit at HEAT mode. If this happens: x The heating operation stops. x The defrost mode will be triggered automatically for about 10 minutes. No intervention is required ; after about 10 minutes, the air conditioner operates again normally. High indoor and outdoor temperatures If both indoor and outdoor temperatures are high and the air conditioner is running at HEAT mode, the outdoor unit's fan and compressor may stop at times. This is normal ; simply wait until the air conditioner switches on again. If a power failure occurs while the air conditioner is operating, the unit will be switched off. [. . . ] Problem Explanation/Solution The air conditioner does not x Check that the breaker used for the air conditioner is switched on. operate at all Wired Remote Controller The air conditioner does not x is displayed on the wired remote controller. One that blows, especially a mechanical device, such as a fan, that produces a current of air. A device for creating a current of air or a breeze. ASSY CONTROL BOX A restraining device of air-condition, measure, or limit. [. . . ]