User manual SAMSUNG GN792IFXA

[. . . ] GN642FFXA GN792IFXA GN952IFXA Manuale di installazione e dell'utente / Piano di cottura da incasso Installation and user manual / Built-in Hotplate Content 1 Preface 2 Safety warning 2. 1 Safety warning 2. 2 Installation 2. 3 Child and people safety 2. 4 During use 2. 5 Cleaning and service 2. 6 Environmental information 4 5 - 11 5 6 7 8 - 9 - 10 11 11 3 Instructions for use and maintenance 3. 1 Description of the appliance 3. 2 How to use the appliance 3. 3 How to turn on 3. 4 How to turn off 3. 5 Safety and energy saving advice 3. 6 Cleaning and maintenance 3. 7 Troubleshooting 3. 8 Application for service 12 - 22 12 - 13 14 15 16 17 18 - 19 - 20 21 22 4 Technical instructions 4. 1 Technical instructions 4. 2 Technical data for engineers 4. 3 Positioning 4. 4 Installing the appliance 4. 5 Gas connection 4. 6 Electrical connection 4. 7 Gas conversion 23 - 30 23 24 25 - 26 27 28 29 30 GB 3 1 Preface Thank you for using our appliance. This booklet explains how the gas hob is best used. In addition to information on its operation, you will also find background information that may be useful when using the product. Keep this booklet in a place where it can be easily found (possible subsequent users can also benefit from it). [. . . ] The special dirt-repelling lacquer has a ceramic filling that makes cleaning easier and substantially improves the durability of the burners. The burner bases are best cleaned with a mild cleaning product and a soft cloth. Pan support, control knobs Take off the pan supports. Clean them and the control knobs with a damp cloth, washing-up liquid and warm water. Stubborn stains are best soaked beforehand. Finally dry everything with a clean soft cloth. Top plate Regularly wipe over the top plate using a soft cloth that has been dampened in warm water to which a dash of washing-up liquid has been added. Dry the top plate thoroughly after cleaning. Thoroughly remove salty foods or liquids from the hob as soon as possible to avoid the risk of corrosion. Stainless steel parts of the appliance may become discoloured over time. This is normal because of the high temperatures. Clean these parts with a product that is suitable for stainless steel each time the appliance is used. GB 19 3. 6 Cleaning and maintenance Burners Remove the burner caps, burner head and burner ring by pulling them upwards and away from the top plate. Soak them in hot water and a little detergent. After cleaning and washing them, wipe and dry them carefully. Make sure that the flame holes are clean and completely dry. Wipe the fixed parts of the burner base with a damp cloth and dry afterwards. Gently wipe the thermocouple and spark plug with a well wrung-out cloth and wipe dry with a clean cloth Make sure that the injector is not blocked before placing the burners back on the top plate. Assemble the auxiliary, semi-rapid, rapid and wok burners as follows Replace the burner head (12) by ensuring that the locating tabs fit into the notches in the burner base (14). 12 14 15 16 11 12 13 14 15 16 Place the burner head (12) on the burner ring (13) so that the thermocouple (15) and the spark plug (16) extend through their respective holes in the burner head. Replace the burner cap (11) by ensuring that the locating tabs fit into the notches in the burner base (14). Replace parts in the correct order after cleaning Do not mix up the top and bottom. The locating lugs must fit exactly into the notches. Set the pan supports down vertically without sliding them over the spillage well. GB 20 3. 6 Cleaning and maintenance Burners Remove the burner caps, burner head and burner ring by pulling them upwards and away from the top plate. Soak them in hot water and a little detergent. After cleaning and washing them, wipe and dry them carefully. Make sure that the flame holes are clean and completely dry. Wipe the fixed parts of the burner base with a damp cloth and dry afterwards. [. . . ] Check the connection for leaks with soapy water. 1/2" ISO 228 1/2" EN 10226-2 1. Place the bracket over the holes that match the size of the screws (see illustration below). Slightly tighten a screw through the bracket so that the bracket is attached to the hob, but so that you can still adjust the position. [. . . ]