User manual SAMSUNG HCN559W ENG (VER.1.0)

[. . . ] HCN479W HCN529W HCN559W HCN5529W HCN659W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PROJECTION TELEVISION SERVICE DIVISION 400 Valley Road, Suite 201 Mount Arlington, NJ 07856 TEL : 1-800-SAMSUNG (1-800-726-7864) www. samsungusa. com . . . . . . . . . . . . . Owner's Instructions BP68-00137A-00 Warning!Important Safety Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. [. . . ] To select a channel over 100, press the +100 button. (For channel 122, press "+100, " then "2, " then "2. ") To change to single-digit channels (0­9) faster, press "0" before the single digit. (For channel "4, " press "0, " then "4. ") Using the Previous Channel Press the PRE-CH button. The TV changes to the last channel you were watching. 36 O P E R AT I O N Selecting Your Favorite Channels You can store of your favorite channels for each available input source (such as TV and CATV). Then, when you press the Fav. CH button on the remote control, the TV displays only the favorite channels you previously stored, allowing you to quickly and easily find frequently watched channels. To Store Your Favorite Channels: 1 Press the MENU button. Press the w button to select "Channel", then press the ENTER button. TV Channel Select Antenna : Air Select Favorite Channels Memorize Channels Add & Delete Channels Fine Tune Channels Check Signal Strenght 2 Press the w button to select "Select Favorite Channels". TV Channel Select Antenna : Air Select Favorite Channels Memorize Channels Add & Delete Channels Fine Tune Channels Check Signal Strenght 3 Press the v or w button to select the channels, then press the ENTER button. Press the ENTER button again to deselect the selected channel. To return to the previous step, move to "Return" by pressing the button and then press the ENTER button. TV TV 6-0 TV 7-0 TV 9-0 TV 11-0 TV 13-0 TV 14-0 TV 16-0 Select Favorite Channels Note: Only memorized channels can be set as Favorite channels. Select All : Press to select all channels. Clear All : Press to clear all channels. w Return Select All w Clear All To View Your Favorite Channels: Press the FAV. CH button repeatedly to jump from one favorite channel to another. 37 O P E R AT I O N Adding and Erasing Channels To add channels that were not memorized (or to delete unwanted channels from memory): TV Channel Channel Select Antenna : Air Select Favorite Channels Memorize Channels Add & Delete Channels Fine Tune Channels Check Signal Strenght 1 Use the number buttons to directly select the channel that will be added or erased. Press the w button to select "Channel", then press the ENTER button. TV 2 Press the w button to select "Add & Delete Channels", then press the ENTER button. TV Channel Select Antenna : Air Select Favorite Channels Memorize Channels Add & Delete Channels Fine Tune Channels Check Signal Strenght 3 Repeatedly pressing ENTER will alternate between Add channel and Delete channel. Press the number buttons (or CH vw buttons) to switch to the appropriate channel, and then repeat step 4. Press ENTER. Add & Delete Channels Channel 11-0 Not In Memory Press ENTER to add the channel Add Return <Add channel> Add & Delete Channels Channel 11-0 In Memory Press ENTER to delete the channel Delete Return <Delete channel> 38 O P E R AT I O N Picture Control You can use the on-screen menus to change the contrast, brightness, tint, color, and sharpness according to personal preference. (Alternatively, you can use one of the "automatic" settings. See next page. ) Customizing the Picture 1 Press the MENU button. Press the w button to select "Picture", then press the ENTER button. TV Picture Picture Mode Custom Picture Color Tone Select Picture Size DNIe Adjust Convergence PIP : Dynamic : Cool 1 : On 2 Press the w button to select "Custom Picture", then press the ENTER button. (The items Contrast, Brightness, Sharpness, Color, and Tint will appear on the screen. ) TV Picture Picture Mode Custom Picture Color Tone Select Picture Size DNIe Adjust Convergence PIP : Dynamic : Cool 1 : On 3 Press the v or w button to select a particular item. TV Contrast Brightness Sharpness Color Tint G 50 Custom Picture 100 45 60 50 R50 4 Press the or button to increase or decrease the value of a particular item. Press the EXIT button to exit. TV Picture Contrast 80 39 O P E R AT I O N Using Automatic Picture Settings Your TV has three automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory. You can activate either Dynamic, Standard or Movie by pressing P. Mode (or by making a selection from the menu). Or, you can select "Custom" which automatically recalls your personalized picture settings. 1 Press the MENU button. Press the w button to select "Picture", then press the ENTER button. TV Picture Picture Mode Custom Picture Color Tone Select Picture Size DNIe Adjust Convergence PIP : Dynamic : Normal : On 2 Press the ENTER button to select "Picture Mode". Press the v or w button to select the "Dynamic" "Standard" "Movie" or "Custom" picture setting. TV Picture Picture Mode Custom Picture Color Tone Select Picture Size DNIe Adjust Convergence PIP Dynamic Standard :Movie Normal Custom : On Alternate method: Simply press the P. Mode button on the remote control to select one of the standard picture settings. Standard · · · · Choose Dynamic for viewing the TV during the day or when there is bright light in the room. [. . . ] When your remote control is in the "VCR" (or CATV or DVD) mode, the volume buttons still control your TV's volume. When your remote is in the "TV" mode, the VCR control buttons (PLAY, PAUSE, etc. ) will still operate your VCR. w w 6 Once your remote control is set up, press the MODE button any time you want to use the remote to operate your VCR (or Cable box or DVD). 80 S P E C I A L F E AT U R E S Setting Up Your Remote Control to Operate Your Cable Box 1 Turn off your cable box. 2 Press the MODE button to select CATV. (CATV mode is displayed on LED screen). The remote control has four "modes": "TV, " "VCR, " "CABLE" and "DVD. " Press the "MODE" button to switch the remote control to the "Cable" mode. w 3 On your Samsung remote control, press SET. 4 Enter 3 digits of the cable box code listed below for your brand of cable box. Make sure you enter 3 digits of the code, even if the first digit is a "0. " (If more than one code listed, try the first one. ) w 5 Press POWER. If your cable box turns on, your remote control is now "set up" correctly. If your cable box does not turn on, repeat steps 2, 3, and 4, but try one of the other codes listed for your particular brand of cable box. [. . . ]