User manual SAMSUNG HL-T6189S

[. . . ] Plug the adapter into the "ANT 1 IN" terminal on the rear panel. Plug the antenna lead into the "ANT 1 IN" terminal on the rear panel. Connecting a DTV Set-Top Box Connecting to Y, PB, PR Connect a set of audio cables between the COMPONENT (1 or 2) audio (L, R) in jacks on the TV and the AUDIO OUT jacks on the Set-Top Box. Connect a set of video cables between the COMPONENT (1 or 2) VIDEO (Y, PB, PR) in jacks on the TV and VIDEO (Y/PB/PR or Y/CB/CR) OUT jacks on the Set-Top Box. Separate VHF and UHF Antennas If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops). Connect both antenna leads to the combiner. [. . . ] Caution: If you want to record one channel while watching another channel, a splitter (not included) must be added between the cable and "ANT 1 IN". One output of the splitter goes to "ANT 1 OUT" and the second output is connected to IN on the cable converter box. If you have a mono VCR, connect L/Mono to VCR Audio OUT using only one audio cable. If you have a S-VHS VCR, use the S-video connections and remove the video cable. Do not connect the video cable and the S-video cable to video1 simultaneously. When you use a converter box with your TV there may be features that you can not program using the remote control, such as programming your favorite channels and blocking channels. TV Rear Panel 15Pin(D-Sub) Cable Audio Cable From Cable Incoming Cable or Antenna DTV Set-Top Box Incoming Cable or Antenna DTV Set-Top Box PC NOTE : The "Anynet" jack is for repairs and software upgrades. VCR NOTE : Please check if the power of HDMI source is on, in case that you fail to select HDMI from the "Source List" even after you connected the cable of HDMI source (DTV Set-Top Box, DVD, etc. ) to TV. Quick Guide Operation Selecting the Video Signal Source Before your TV can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i. e. , an antenna or a cable system). Front Panel LED Indicators Storing Channels in Memory (Automatic Method) First, select the correct signal source ("Air", "STD", "HRC" or "IRC") as described before. The three lights on the front panel indicate the status of your TV. Your New Wide TV Remote Control You can use the remote control up to about 23 feet from the TV. When using the remote control, always point it directly at the TV. You can also use your remote control to operate your Set-Top Box, VCR, Cable box or DVD player. Press the MENU button. or button to select "Channel", then press the ENTER button. or button to select "Air/CATV", then press the ENTER button. PIP Controls SWAP; Press to exchange the video signal that is currently displayed on the main screen with the signal in the PIP window. CH / ; Press to display the available channels in sequence. (These buttons change channels in the PIP window only. ) 27. VCR/DVD Controls Controls VCR or DVD functions: Rewind, Stop, Play/Pause, Fast Forward. RESET If your remote control is not functioning properly, take out the batteries and press the reset button for about 2~3 seconds. Re-insert the batteries and try using the remote control again. Auto Program Channel Input Picture Sound Channel Setup Antenna : Air Ant. 1 Air/CATV : STD Air Auto Program HRC Add/Delete IRC Favorite Channels Name Fine Tune More Move Enter Return Start Enter Auto Program Air 11 Stop Enter Return Return Special Features Customizing Your Remote Control Your TV comes equipped with a universal remote control. In addition to controlling the TV, the universal remote control can also operate a VCR, Cable box, DVD and Set-Top Box made by Samsung (even if your VCR, Cable box and DVD are made by manufacturers other than Samsung). NOTE : The remote control might not be compatible with all VCRs, DVD players and Cable boxes. 7. Anynet Runs the Anynet view functions and sets up the Anynet devices. STILL Press to stop the action during a particular scene. P. SIZE Press to change the picture size. [. . . ] If your VCR (Cable box or DVD player) does not turn on, repeat steps 2, 3, and 4, but try one of the other codes listed for the brand of your particular VCR (Cable box or DVD player). Once your remote control is set up, press the MODE button any time you want to use the remote to operate your VCR (Cable box or DVD player). NOTES · When your remote is in the TV mode, the VCR (or DVD player) control buttons (REW, STOP, PLAY/PAUSE and FF) will still operate your VCR (or DVD player). · When your remote control is in the STB, VCR, CABLE or DVD mode, the volume buttons still control your TV's volume. [. . . ]