User manual SAMSUNG HT-AS601

[. . . ] SAMSUNG ELECTRONICS AMERICA, INC. SERVICE DIVISION 400 Valley Road, Suite 201 Mount Arlington, NJ 07856 1-800-SAMSUNG (1-800-726-7864) www. samsung. com ELECTRONICS AH68-01751R Digital Surround AV Receiver System HT-AS601B Instruction Manual Safety Warnings CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Note to CATV system installer : This reminder is provided to call the CATV system installer's attention to Section 820~40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical This symbol indicates that dangerous voltage which can cause electric shock is present inside this unit. This symbol alerts you to important operating and maintenance instructions accompanying the unit. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. 1 Precautions PREPARATION Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). [. . . ] · YES(Subwoofer) : Select this when you use Subwoofer Speaker. · NO(Subwoofer) : Select when you do not use Subwoofer Speaker. · CROVR: Select the crossover frequency for the best bass response in your room. 20 Setting the Speaker Listening Distance REMOTE CONTROL 1 Press the SPEAKER DISTANCE button to select the speaker you want. · Each time you press this button, F. L CEN F. R S. R S. B S. L S. W DISTANCE OFF will be selected in turn. set the speaker distance. button toSpeaker, you can set the distance from the speaker to For F. L, CEN, F. R, S. W · listening position between 0. 0~5feet in intervals of 1 foot. · For S. R, S. B, S. L Speaker, you can set the distance from the speaker to listening position between 0. 0~15feet in intervals of 1 foot. To Exit Setup Mode · Wait for about 5 seconds or press the SPEAKER DISTANCE button of remote control to select DISTANCE OFF. · If the listening position is beyond the range of speaker distance setup when you place the speaker, set the speaker distance to the maximum. 21 MAIN UNIT button. 1 Press SETUPappears on the display and enters into Setup Mode. "SETUP MODE" 2 Press INPUT button 2 times. · OPERATION · "DISTANCE SETUP" appears on the display. SURROUND button speaker you want. 3 Presstime you press this button, F. Ltoselect the S. R S. B S. L S. W Each CEN F. R · will be selected in turn. 4 Press SELECT( , ) button to set the speaker distance. · For F. L, CEN, F. R, S. W Speaker, you can set the distance from the speaker to listening position between 0. 0~5feet in intervals of 1 foot. · For S. R, S. B, S. L Speaker, you can set the distance from the speaker to listening position between 0. 0~15feet in intervals of 1 foot. To Exit Setup Mode · Wait for about 5 seconds or turn the VOLUME CONTROL of the main unit. "SETUP MODE OFF" appears on the display and exit Setup Mode. Setting Speaker Distance Set the distance from the speaker to listening position in intervals of 1 foot. · F. L (Front-Left) : 0 ~ 5feet · CEN (Center) : 0 ~ 5feet · F. R (Front-Right) : 0 ~ 5feet · S. R (Surround-Right) : 0 ~ 15feet · S. B (Surround Back) : 0 ~ 15feet · S. L (Rear-Left) : 0 ~ 15feet · SW (Subwoofer) : 0 ~ 5feet 22 Setting DRC (Dynamic Range Compression) You can use this function to enjoy Dolby Digital sound when watching movies at low volume at night. MAIN UNIT button. 1 Press SETUPappears on the display and enters into Setup Mode. "SETUP MODE" 2 Press INPUT button 3 times. · · "DRC SETUP" appears on the display. 3 Press SURROUND button to set DRC. · Each time you press this button, DRC : STD DRC : MAX DRC : MIN will be selected in turn. To Exit Setup Mode · Wait for about 5 seconds or turn the VOLUME CONTROL of the main unit. "SETUP MODE OFF" appears on the display and the unit exits Setup Mode. Setting DRC · STD : Sets DRC effect to standard. · MAX : Sets DRC effect to maximum. · MIN : Sets DRC effect to minimum. · You can only set this function via the main unit. 23 Test Tone Use the test tone to check the speaker connection status or level. To Automatically Output Test Tone REMOTE CONTROL 1 Press TEST TONE button. · Test signal will be automatically output as follows; F. L CEN F. R S. R S. B S. L S. W. · During test tone output, press . . . button to adjust the speaker output level from -10 to +10 dB by 1 step. OPERATION To Stop Test Tone · Press TEST TONE button again. 24 Test Tone Use the test tone to check speaker connection status or level. To Automatically Output Test Tone MAIN UNIT button. 1 Press SETUPappears on the display and enters into Setup Mode. "SETUP MODE" 2 Press INPUT button 4 times. "TEST-T AUTO" appears in the display. 3 Press SURROUND button. · · · Test signal will be automatically output as follows; F. L CEN F. R S. R S. B S. L S. W . · During test signal output, press SELECT ( , ) button to adjust the speaker output level from -10 to +10 dB by 1 step. To Stop Test Tone Method 1) Press INPUT button 2 times. · "TEST-T OFF" appears on the display and test tone stops. Method 2) Turn VOLUME CONTROL. · "SETUP MODE OFF" appears on the display and test tone stops. 25 To Manually Output Test Tone OPERATION MAIN UNIT button. 1 Press SETUPappears on the display and the unit enters into Setup Mode. "SETUP MODE" 2 Press INPUT button 5 times. · · "TEST-T MANU" appears in the display. 3 Press SURROUND button. will be selected in turn. · · Each time you press this button, F. L CEN F. R S. R S. B S. L S. W , )button test as 4 Press SELECT(speaker output levelto set the+10dBtonestep. you want. [. . . ] (SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of: One (1) Year Parts and Labor* (*90 Days Parts and Labor for Commercial Use) This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States. To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures. Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG's authorized service center. [. . . ]