User manual SAMSUNG HT-AS610T/XAC

[. . . ] HEADQUARTERS 55 Standish Court Mississauga, Ontario L5R 4B2 Canada TEL: 1-905-542-3535 www. samsung. ca SERVICE DIVISION 55 Standish Court Mississauga, Ontario L5R 4B2 Canada 1-800-SAMSUNG (1-800-726-7864) AH68-01853S Digital Surround AV Receiver System HT-AS610 Instruction Manual (AV-R610) Safety Warnings CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Note to CATV system installer : This reminder is provided to call the CATV system installer's attention to Section 820~40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical This symbol indicates that dangerous voltage which can cause electric shock is present inside this unit. This symbol alerts you to important operating and maintenance instructions accompanying the unit. WARNING : To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. 2 Precautions PREPARATION VOLUME Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). [. . . ] "SETUP MODE" 2 Press FUNCTION button 4 times. · · "DRC SETUP" appears on the display. OPERATION button. "DRC STD" appears on 4 Press SELECT( , ) button to set DRC. · · Each time you press this button, DRC : STD DRC : MAX DRC : MIN will be selected in turn. To Exit Setup Mode · Wait for about 5 seconds or press SETUP button. "SETUP MODE OFF" appears on the display and the unit exits Setup Mode. Setting DRC · STD : Sets DRC effect to standard. · MAX : Sets DRC effect to maximum. · MIN : Sets DRC effect to minimum. 25 Test Tone Use test tone to check the speaker connection status or level. To Automatically Output Test Tone REMOTE CONTROL Press TEST TONE button. · Test signal will be automatically output as follows; F. L CEN F. R S. R S. L S. W. · During test tone output, press . . . button to adjust the speaker output level from -10 to +10 dB by 1 step. To Stop Test Tone · Press TEST TONE button again. MAIN UNIT button. 1 Press SETUPappears on the display and enters into Setup Mode. "SETUP MODE" 2 Press FUNCTION button 5 times. "TEST-T AUTO" appears in the display. 3 Press SURROUND button. · · · Test signal will be automatically output as follows; F. L CEN F. R S. R S. L S. W . · During test signal output, press SELECT ( , ) button to adjust the speaker output level from -10 to +10 dB by 1 step. To Stop Test Tone Press SETUP button 1 time. · "SETUP MODE OFF" appears on the display and test tone stops. 26 To Manually Output Test Tone OPERATION MAIN UNIT button. 1 Press SETUPappears on the display and the unit enters into Setup Mode. "SETUP MODE" 2 Press FUNCTION button 6 times. · · "TEST-T MANU" appears in the display. 3 Press SURROUND button. be selected in turn. · Each time you press this button, F. L CEN F. R S. R S. L S. W will 4 Press SELECT( want. , ) button to set the test tone as you · You can adjust the speaker output level from -10 to +10dB by 1 step. · The sound gets quieter at -10dB and louder at +10dB. To Stop Test Tone Press SETUP button 1 time. · "SETUP MODE OFF" appears on the display and test signal stops. Test Tone Output · F. L (Front-Left) : -10 ~ +10dB · CEN (Center) : -10 ~ +10dB · F. R (Front-Right) : -10 ~ +10dB · S. R (Surround-Right) : -10 ~ +10dB · S. L (Surround-Left): -10 ~ +10dB · S. W (Subwoofer): -10 ~ +10dB 27 Setting Speaker Level You can set the balance and level of speakers Remote Control SPK the 1 Presstime youLEVEL button to select F. R speaker you want. Each press this button, F. L CEN S. R S. L S. W · SPK LVL OFF will be selected in turn. to set the speaker 2 Press . . . You can adjust it from · · The sound gets quieter at -10dB and louder at +10dB. · Default setting value is 00dB. To Exit Setup Mode · Wait for about 5 seconds or press SPK LEVEL button on the remote control to select SPK LVL OFF. 28 MAIN UNIT 1 Press SETUP button. · "SETUP MODE" appears on the display and enters into Setup Mode. 8 times. "LEVEL SETUP" appears on the · OPERATION SURROUND button. 3 Presstime you press this button, F. L CEN F. R S. R S. L S. W Each · will be selected in turn. 4 Press SELECT( you want. , ) button to set to the speaker level · You can adjust it from -10 to +10dB by 1 step. · The sound gets smaller at -10dB and louder at +10dB. · Default setting value is 00dB To Exit Setup Mode · Wait for about 5 seconds or press SETUP button. "SETUP MODE OFF" appears on the display and exits Setup Menu. Setting Speaker Level · F. L (Front-Left) : -10 ~ +10dB · CEN (Center) : -10 ~ +10dB · F. R (Front-Right) : -10 ~ +10dB · S. R (Surround-Right) : -10 ~ +10dB · S. L (Surround-Left): -10 ~ +10dB · S. W (Subwoofer): -10 ~ +10dB 29 Dolby Pro Logic ll Mode This mode provides 5. 1 channel sound from 2 channel sources REMOTE CONTROL Press MODE button. · Each time you press this button, CINEMA MATRIX GAME PROLOGIC MUSIC will be selected in turn. To Exit Setup Mode · Wait for about 5 seconds. 30 MAIN UNIT 1 Press SURROUND button to select "DPL ll" Mode. · Each time you press this button, DPL ll SFE STEREO will be selected in turn. 2 Press SELECT( OPERATION , ) button. ) button, CINEMA MATRIX GAME PROLOGIC MUSIC will be selected in turn. · Each time you press SELECT ( ) button, MUSIC PROLOGIC GAME MATRIX CINEMA will be selected in turn. · Each time you press SELECT ( To Exit Setup Mode · Wait for about 5 seconds. Dolby Pro Logic ll Mode · MUSIC : Provides 5. 1 Channel Surround sound to digital, analog · You cannot use Dolby Pro Logic ll Mode for multi channel or existing stereo sources such as CD, TAPE, FM, TV and Stereo VCR. · CINEMA : Adds realism to the movie soundtrack. · MATRIX : You will hear 5. 1 Channel Surround sound. [. . . ] · Is the speaker setup selected to NONE? SMALL or YES. Picture does not appear when the function is selected. The sound from each device is changed during stereo playback. Can't receive broadcasting. · Isn't the external component connected · Properly connect it. properly? · Are the batteries exhausted?· Is the distance between remote · Replace with new batteries. [. . . ]