User manual SAMSUNG HT-AS720

[. . . ] Digital Surround AV Receiver System HT-AS720S Instruction Manual SAMSUNG ELECTRONICS CANADA, INC. HEADQUARTERS 55 Standish Court Mississauga, Ontario L5R 4B2 Canada TEL:1-905-542-3535 www. samsung. ca SERVICE DIVISION 55 Standish Court Mississauga, Ontario L5R 4B2 Canada 1-800-SAMSUNG (1-800-726-7864) Safety Warnings Precautions ENG PREPARATION CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. SERVICE PERSONNEL. Note to CATV system installer : This reminder is provided to call the CATV system installer 's attention to Section 820~40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. [. . . ] : TV will be selected Each HDMI in turn. To exit setup mode · Wait for about 5 seconds or press SETUP/MENU button. "SETUP OFF" appears on the display and Setup Mode is exited. To exit setup mode · Wait for about 5 seconds or press SETUP/MENU button. Using the DRC button Press DRC button. · Each time you press this button, DRC : STD DRC : MAX DRC : MIN will be "SETUP OFF" appears on the display and Setup Mode is exited. selected in turn. Setting HDMI AUDIO · AVR : Audio is played on this product. · TV : Audio is played on a TV connected to the HDMI OUT jack and no audio is Setting DRC · STD : Sets DRC effect to standard. · MAX : Sets DRC effect to maximum. · MIN : Sets DRC effect to minimum. played on this product. · HDMI AUDIO setting is available only when the HDMI output is connected to a TV. · If you do not hear sound from the TV, should change the HDMI audio output setting for your DVD PLAYER or SAT to PCM. 24 25 Test tone Use the test tone check the speaker connection status or level. ENG To automatically output test tone To Manually Output Test Tone 1 Press SETUP/MENU button, and then press the ENTER button. · "SETUP MODE" appears on the display and the unit goes into Setup Mode. 1 Press SETUP/MENU button, and then press the ENTER button. · "SETUP MODE" appears on the display and goes into Setup Mode. Press button 2 and then press theto select the "TEST-T AUTO", ENTER button. · Test signal will be automatically output as follows; F. L CEN F. R 2 Press ¤ button to select the "TEST-T MANU", and then press the ENTER button. 3 Presstime youbutton to selectF. L speaker youS. R SBR SBL Each press ¤¤button, CEN F. R · S. R SBR SBL S. L S. W . OPERATION · During test signal output, press . . . button to adjust the individual speaker output level from -10 to +10 dB by 1 step. S. L S. W will be selected in turn. To stop test tone · Press SETUP/MENU button once time. 4 Press . . . button to set the test tone as you want. · You can adjust the speaker output level from -10 to +10dB by 1 step. · The sound gets quieter at -10dB and louder at +10dB. "SETUP OFF" appears on the display and test tone stops. To stop test tone · Press SETUP/MENU button once time. Using the Test Tone button Press TEST TONE button. · Test signal will be automatically output as follows; F. L CEN F. R S. R "SETUP OFF" appears on the display and test tone stops. SBR SBL S. L S. W. · During test tone output, press . . . button to adjust the speaker output level from -10 to +10 dB by 1 step. Test Tone Output · F. L (front left) : -10 ~ +10dB · CEN (center) : -10 ~ +10dB · F. R (front right) : -10 ~ +10dB · S. R (surround right) : -10 ~ +10dB · SBR (surround back right) : -10 ~ +10dB · SBL (surround back left) : -10 ~ +10dB · S. L (surround left) : -10 ~ +10dB · S. W (subwoofer) : -10 ~ +10dB 26 27 Setting speaker level You can set the balance and level of speakers. Dolby Pro Logic llx mode This mode provides 7. 1 channel sound from 2 channel sources. ENG REMOTE CONTROL Press MODE button. · Each time you press this button, CINEMA MATRIX GAME 1 Press SETUP/MENU button, and then press the ENTER button. · "SETUP MODE" appears on the display and goes into Setup Mode. PL MUSIC will be selected in turn. 2 Press 3 Press button to select the "LEVEL SETUP", and then press the ENTER button. button to select the speaker you want. button, F. L CEN F. R S. R SBR SBL S. L S. W will be selected in turn. · Each time you press MAIN UNIT SURROUND button to 1 Presstime you press this button, DPLIIxselect "DPLIIx"mode. Each NEO:6 SFE STEREO · 4 Press . . . button to set the speaker mode. · You can adjust it from -10 to +10dB by 1 step. · The sound gets quieter at -10dB and louder at +10dB. OPERATION will be selected in turn. 2 Press SELECT( , ) button. To exit setup mode · Wait for about 5 seconds or press SETUP/MENU button. · Each time you press SELECT ( ) button, CINEMA MATRIX GAME PL MUSIC will be selected in turn. ) button, MUSIC PL GAME MATRIX CINEMA will be selected in turn. "SETUP OFF" appears on the display and Setup Mode is exited. · Each time you press SELECT ( Using the SPK LEVEL button 1 Press SPK LEVEL button to select the speaker you want. · Each time you press this button, F. L CEN F. R S. R SBR SBL S. L To exit setup mode · Wait for about 5 seconds. Dolby Pro Logic llx mode · MUSIC : Provides 7. 1 channel surround sound for digital, analog or existing stereo S. W SPK LVL OFF will be selected in turn. 2 Press . . . button to set the speaker level you want. · You can adjust it from -10 to +10dB by 1 step. · The sound gets quieter at -10dB and louder at +10dB. sources such as CD, TAPE, FM, TV and stereo VCR. · CINEMA : Adds realism to the movie soundtrack. · MATRIX : You will hear 7. 1 channel surround sound. · GAME : Enhances the excitement of the game's sound. · PL : You will experience a surround effect with just the front left and right speakers. Setting Speaker Level · F. L (front left) : -10 ~ +10dB · CEN (center) : -10 ~ +10dB · F. R (front right) : -10 ~ +10dB · S. R (surround right) : -10 ~ +10dB · SBR (surround back right) : -10 ~ +10dB · SBL (surround back left) : -10 ~ +10dB · S. L (surround left) : -10 ~ +10dB · S. W (subwoofer) : -10 ~ +10dB · You cannot use Dolby Pro Logic llx mode for multi channel signals such as Dolby Digital and DTS. · Pro Logic works only for PCM audio signals with sampling frequencies of 32KHz, 44KHz or 48KHz. · Sound will not be output from the surround back speaker if the PCM audio signal is mono. 28 29 Setting Dolby Pro Logic llx effect This function works only in Dolby PRO LOGIC IIx MUSIC Mode. Setting NEO:6 mode You can play back 2 channel sound over 6. 1 channels when enjoying music or a movie. ENG Press 1 button. SETUP/MENU button, and then press the ENTER · "SETUP MODE" appears on the display and goes into Setup Mode. REMOTE CONTROL Press NEO:6 MODE button. · Each time you press this button, MUSIC CINEMA will be selected in turn. 2 Press 3 4 Press button to select the " and then press the ENTER button. button. MODE", MAIN UNIT SURROUND button briefly to select "NEO:6" mode. 1 Presstime you press this button, DPLIIx NEO:6 SFE STEREO will Each · be selected in turn. · Each time you press this button, C-WIDTH DIMENSION PANORAMA will be selected in turn. SELECT( ) 2 Presstime you press this, button, button. button to set the Dolby Pro Logic llx effect you want. To set the height of the center sound image If your TV (or screen) is installed high on a wall, you can raise the center sound image of the front and center speakers to compensate. OPERATION To exit setup mode · Wait for about 5 seconds or press SETUP/MENU button. "SETUP OFF" appears on the display and Setup Mode is exited. 1 Press SETUP/MENU button, and then press the ENTER button. [. . . ] · Check the left/right channel and connect DAYTRON DBX EMERSON FISHER FUNAI GENERAL ELECTRIC (GE) GO VIDEO HARMAN KARDON HITACHI HQ INSTANT REPLAY JCL JCP JC PENNY JVC KENWOOD LG (GOLDSTAR) Code Number 003, 032 019 017 002 006 012 010, 013 008 001 004 005, 016 004, 014 011 021 006 004, 023 007, 011, 022, 025 006 000, 027 002 015, 020 011 004, 018 009, 033 004, 024 026 028 029 030 031 control and main unit too great? · Are the left/right speaker or left/right REALISTIC input/output cables connected properly? · Is FM antenna connected properly? it/them correctly. · Connect the antenna correctly. · If the input strength of antenna signal is SAMSUNG weak, install the FM antenna in a place with good reception. · Is the surround speaker connected · Refer to pages 10~11 to connect them MISCELLANEOUS SANYO SANSUI SCOTT SEARS SHARP SINGER SIGNATURE 2000 (M. WARDS) SHINTOM SONY properly? properly. · Refer to pages 20~21 to select LARGE or There is no sound from surround speakers. · Is SURR (surround) incorrectly set to NONE in speaker setup? · Is surround mode set to stereo?· Is the center speaker connected properly? SMALL. · Refer to pages 29~35 to select proper Surround Mode. · Refer to pages 10~11 to connect it properly. · Refer to pages 20~21 to select LARGE or LXI (SEARS) MAGIN MAGNAVOX MARANTZ MARTA There is no sound from center speaker · Is CEN (center) incorrectly selected to NONE in speaker setup? · Is the surround mode selected to stereo? SMALL. · Refer to pages 29~35 to select other STS SYLVANIA SYMPHONIC TANDY Surround Modes. 44 45 Before calling for service (cont'd) Symptom There is no sound from surround back speakers Specifications Power supply Standby power consumption Main unit Power consumption Subwoofer Weight Dimensions (W x H x D) Operating temperature range Operating humidity range Frequency response Usable sensitivity S/N ratio Distortion Stereo separation Tuner output level Rated output Front speaker(left+right) Center speaker Surround speaker(left+right) Surround back Input sensitivity/impedance S/N ratio (analog input) Separation (1kHz) Analog input Digital input/96kHz PCM TV format Input level/impedance Output level/impedance Video frequency response S/N ratio Front / Surround 4 x 4 100W 200W 3. 9 x 10. 6 x 3. 8 inches 3. 1 Ibs / 2. 6 Ibs 120V, 60 Hz 0. 9W 100W 90W 12. 7 Ibs 16. 9 x 5. 7 x 13. 7 inches 41°F~+95°F 10%~75% 87. 5~108. 0MHz 12dBf MONO/STEREO 55/55dB MONO/STEREO 0. 3/0. 8% 30dB 1kHz, 75kHz Dev 20Hz~20kHz/THD = 10% 4 100W/CH 4 100W/CH 4 100W/CH 4 100W/CH 450mV/47k 80dB 60dB 20Hz~20kHz(±3dB) 20Hz ~44kHz(±3dB) NTSC/PAL 1Vp-p/75 1Vp-p/75 5Hz to 10kHz(-3dB) 60dB Subwoofer speaker Center 8 4 150W 100W 300W 200W 11. 8 x 3. 5 x 3. 7 inches 12 x 15. 6 x 17. 4 inches 3. 1 Ibs 31. 7 Ibs ENG Check · Are the surround back speakers Remedy · Refer to pages 10~11 to connect it properly. connected properly? · Is the S. BACK(Surround Back) selected · Refer to pages 20~21 to select LARGE or GENERAL SMALL. · Refer to page 32 to set Surround Mode to EX/ES. [. . . ]