User manual SAMSUNG L330

[. . . ] To avoid injuries or damage to property, please read the following precautions carefully and use the product accordingly. Failure to follow the instructions marked with this symbol may cause personal injury or even fatality. Failure to follow the instructions marked with this symbol may cause personal injury or damage to the product or property. | Power Related | Installation Related | Cleaning and Use Related | [The images here are for reference only, and are not applicable in all cases (or countries). ] Insert the power plug firmly so that it does not come loose. When the connection is not firm, it may cause a fire. Do not use loose power outlets or damaged power cables. [. . . ] If not, there may be signal problems. | Basic Settings | Connecting the Power | Connecting an External Device | 1. Rear of Projector Plug the power cord into the power terminal on the rear of the projector. | Basic Settings | Connecting the Power | Connecting an External Device | Connecting a PC using the D-Sub cable Check that your PC and projector are turned off. Connect the [PC IN (1 or 2)] terminal at the back of the projector to the D-Sub terminal of your PC using the D-Sub cable. - For the supported input signals, refer to "PC Timing(D-Sub/HDMI)". Connect the [PC 1/DVI AUDIO IN] or [AUDIO IN 2] terminal at the back of the projector to the Audio out terminal of your PC using an audio cable (Not supplied). Connecting a PC using an HDMI/DVI cable Check that your PC and projector are turned off. Connect the [HDMI/DVI IN] terminal of the projector to the HDMI or DVI terminal of your PC using a HDMI/HDMI or HDMI/DVI cable (Not supplied). - When connecting to the HDMI terminal of your PC, use an HDMI cable (Not supplied). - For the supported input signals, refer to "PC Timing(D-Sub/HDMI)". Connect the [PC 1/DVI AUDIO IN] terminal of the projector and the Audio out terminal of your PC using an audio cable (Not supplied). - If connecting with an HDMI/HDMI cable, an audio cable (Not supplied) is not needed. Connecting an External Monitor You can view an image on both your projector and a separate monitor at the same time. Check that your PC and projector are turned off. Connect the [PC IN 1] terminal at the back of the projector to the D-Sub terminal of your PC using a D-Sub cable. Connect the [PC OUT] terminal of the projector to the D-Sub terminal of a monitor using a D-Sub cable. - When connecting a monitor using the [PC OUT] function, make sure to connect your PC to the [PC IN 1] terminal. - The monitor output which is connected to the [PC OUT] termininal will be normal even if you see a blank screen on your projector. - The [PC OUT] function also operates in standby mode. Connecting an HDMI-Compatible Device First, check that the AV device and your projector are turned off. Connect the [HDMI/DVI IN] terminal at the back of the projector to the HDMI or HDMI/DVI output terminal of the digital output device using an HDMI/DVI cable. - When connecting to the HDMI output terminal of the digital output device, use an HDMI cable. - For the supported input signals, refer to "AV Timing(HDMI)". Connect the [PC 1/DVI AUDIO IN] terminal of the projector to the Audio out terminal of your digital output device using an audio cable (Not supplied). - If connecting with an HDMI/HDMI cable, an audio cable (Not supplied) is not needed. Connecting an AV device using a D-Sub cable First, check that the AV device and your projector are turned off. Connect the [PC IN (1 or 2)] terminal at the back of the projector to the D-Sub terminal of your AV device using a D-Sub cable. - For supported input signals, refer to the "AV Timing (D-Sub)". [. . . ] Check that the power cord is unplugged before replacing the lamp. Since the lamp is a high temperature and high voltage product, wait at least one hour from the time that the power cord is disconnected before replacing it. The lamp is located on the left side of the projector (when looking from the front). Do not leave the old lamp near inflammables or in reach of children. [. . . ]