User manual SAMSUNG LN46C540F2F

[. . . ] Stand the product up and fasten the screws. If you fasten the screws with the LCD TV placed down, it may lean to one side. 1 DVI OUT USB2 AV IN 2 Device AUDIO OUT DVD / Blu-Ray player / Cable Box / Satellite receiver (STB) Connecting a PC Connect your TV to a PC to use it as a Monitor. Guide Stand Front 2 AV IN 2 HDMI IN 4 (HDD) USB1 USB1 Very Good Connection LN32C530 / LN37C530 / LN40C530 / LN46C530 Stand Component connection (up to 1080p) Using a Component Cable AUDIO OUT s s s s COMPONENT OUT Device HD connection Using an HDMI Cable Rear s s s Audio/Video connection (480i only) Bottom View Top View s VCR / DVD / Blu-ray player / Cable Box / Satellite receiver AUDIO OUT DVI OUT Using an Audio/Video Cable VIDEO OUT AUDIO OUT VCR When connecting to AV 1 on the back of your TV, Good Connection USB2 PC VCR / DVD / Blu-ray player / Cable Box / Satellite receiver attach the video cable (yellow) to the green jack next to the AV In 1 label. The jack will not match the color of the video cable (yellow). HDMI IN 4 Screw 3 s s s s (HDD) USB1 Lowest Quality Connection AV IN 2 Using an D-Sub Cable PC OUT AUDIO OUT LN40C540 / LN46C540 HD connection (up to 1080p) Step 2 : Install the Batteries into the Remote To install batteries into your remote control, follow these steps: 1. Lift the cover on the back of the remote upward as shown in the figure to the right. [. . . ] Select Manual if you don't, or if you have a cable or satellite box. The Daylight Savings screen appears. FAV. CH MEDIA. P Adjust the volume by pressing the y button on the remote. TOOLS INFO 6. If your TV is attached to a cable RETURN INFO Plug & Play Select language of the OSD. language english español Français U Move E enter RETURN EXIT or satellite box, you change the channel using the box's remote. EXIT If you select Manual, the clock setting screen appears. 7. Select the daylight saving time setting: Off, On, or Auto, and then press enTerE button. After the time zone screen, The connection method for best HD screen quality is displayed. Press Right arrow button on your remote to view each screen in succession. Press the Blue button to skip this section. and then press enTerE button. Wide Fit 4:3 Standard screen Screen Fit 16:9 Wide screen Zoom 1 Zoom 2 S. MODE You can also change theSLEEP channels by pressing the P. MODE P. SIZE z buttons on the front panel of your TV and adjust the volume by pressing the y buttons. MTS CC S. MODE P. MODE SLEEP P. SIZE MTS CC : english Remote control sensor Power Indicator 1. On the Language screen, select the language for the On Screen Display (OSD) using your remote control, and then press enTerE button. Select Home Use, and then press enTerE button. If you select Store Demo, the TV will reset your picture and audio settings every 30 minutes. After you press enTerE button, the Antenna Source screen appears. If your TV is only attached to an antenna, select Air. If your TV is only attached to cable and you have no cable box, select Cable. If your TV is attached to an antenna and cable with no box, select Auto. When done, press enTerE button on your remote. IMPORTANT: If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4, according to the directions for your cable or satellite box. 9. 2. Basic Functions Selecting a Source To watch a movie on your Blu-ray player or watch your favorite TV show, you must select the correct source. A source is a device, such as a Blu-ray/DVD player, a cable/satellite box, antenna or a cable TV input. Sources can be connected to your TV through the HDMI, DVI, Component, Composite, or D-sub connections, or through the Antenna or Cable In connections. [. . . ] Press the reTUrn button on your remote when done. To change the Picture Mode, follow these steps: 1. FAV. CH With the TV on, press the TOOlS button on your remote. Using the or on your remote, select Picture mode. On the Picture Mode menu, use the or on your remote to select the Picture Mode you want. Press the exIT button to exit the menu. PRE-CH Press number buttons for direct access to channels. TOOLS 2. INFO 3. [. . . ]