User manual SAMSUNG LT15M23C OPEN SOURCE GUIDE (VER.1.1)

[. . . ] It is dangerous to make any kind of contact with any inside part of this product. This symbol alerts you that important literature concerning operation and maintenance has been included with this product. Note to CATV system installer: This reminder is provided to call CATV system installer's attention to Article 820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. Caution: FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may void the user's authority to operate it. Caution: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug. [. . . ] Press the VOL + button to display the Picture menu. Picture Mode Contrast Brightness Shar pness Color Tint Color Tone Normal Custom Move Sel ect Menu 2 Press the CH w or CH v buttons to select a particular item. Picture Mode Contrast Brightness Shar pness Color Tint Color Tone Normal Custom The customer can select "Normal", "Warm", or "Cool" according to personal preference. w Move Aj ust Menu 3 Press the VOL + or VOL ­ buttons to increase or decrease the value of a particular item. For example, if you select "Contrast, " pressing VOL + increases it. Press the MENU button to exit. CHAPTER THREE: TV OPERATION 3. 10 O P E R AT I O N Using Automatic Picture Settings Your TV has two automatic picture settings ("Standard", "Mild" and "Dynamic") that are preset at the factory. You can activate either Standard, Mild or Dynamic by pressing P. STD (or by making a selection from the menu). Or, you can select "Custom" which automatically recalls your personalized picture settings. 1 Press the MENU button to display the menu. Press the VOL + button to display the Picture menu. Picture Mode Contrast Brightness Shar pness Color Tint Color Tone Normal Custom Move Sel ect Menu 2 Press the VOL +or VOL buttons to select the "Standard, " "Mild, " "Dynamic" or "Custom" picture setting. Picture Mode Contrast Brightness Shar pness Color Tint Color Tone Normal Standard Move Sel ect Menu Alternate method: Simply press the P. STD button on the remote control to select one of the standard picture settings. · · · · Choose Standard for the standard factory settings. Choose Mild ("Mild Contrast") when viewing the TV in low light, or when playing video games. Choose Dynamic to increase the clarity and sharpness of the picture. Choose Custom if you want to adjust the settings accordings to personal preference (see "Customizing the Picture, page 3. 10). 3. 11 CHAPTER THREE: TV OPERATION O P E R AT I O N Customizing the Sound The sound settings can be adjusted to suit your personal preference. (Alternatively, you can use one of the "automatic" settings. See next page. ) 1 Press the MENU button to display the menu. · Not available if V-Chip is turned on. · Normal sound will still be heard. Press again ti cancel. CHAPTER FOUR: SPECIAL FEATURES 4. 4 S P E C I A L F E AT U R E S Special Sound Options Choosing a Multi-Channel Sound (MTS) Soundtrack Depending on the particular program being broadcast, you can listen to stereo, mono, or a Separate Audio Program. (SAP audio is usually a foreign-language translation. Sometimes SAP has unrelated information like news or weather. ) 1 Press the MENU button to display the menu. Press the CHw button to select "Sound", then press the VOL + button Sound Mode Equalizer Vir tual Dolby Auto Volume MTS Setting MTS Headphone Sound Select Main : Off : Off : Manual Mono Custom Move Sel ect Menu 2 Press the CHw button three times to select "MTS". Mode Equalizer Vir tual Dolby Auto Volume MTS Setting MTS Headphone Sound Select Sound Custom : Off : Off : Manual Mono Main Move Sel ect Menu 3 Press the VOL + button repeatedly to select "Mono, " "SAP, " or "Stereo. " Press the MENU button to exit Sound Mode Equalizer Vir tual Dolby Auto Volume MTS Setting MTS Headphone Sound Select Main : Off : Off : Manual Stereo Custom The text at the bottom of the menu tells you if the incoming audio is stereo, SAP, or mono. w Move Sel ect Menu · · · Choose Stereo for channels that are broadcasting in stereo. Choose Mono for channels that are broadcasting in mono, or if you are having difficulty receiving a stereo signal. Choose SAP to listen to the Separate Audio Program, which is usually a foreign-language translation. You can also change the MTS setting by pressing the "MTS" button on the remote control. (When you change channels, MTS is set to "Stereo" automatically. To listen in `SAP' or `Mono, ' change the MTS setting. ) 4. 5 CHAPTER FOUR: SPECIAL FEATURES S P E C I A L F E AT U R E S Auto Volume Each broadcasting station has its own signal conditions, and it is inconvenient to adjust the volume every time the channel is changed. "Auto volume" automatically adjusts the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low. 1 Press the MENU button to display the menu. [. . . ] Mark the four corner openings and drill four 5/8-dia. Assemble the wall mount kit according to the instructions provided with it. Securely attach Ergotron's flat panel, triple pivot direct mount adapter to the back of the TV using the four 4mm, . 7 pitch x 10mm screws provided with the arm. Secure the assembly to the wall using four 3/16 by 3-inch long toggle bolts. A. 2 APPENDIX APPENDIX Attaching a Wall or Arm mounting device The TV supports VESA mounting standard for use with various VESA mounting devices. [. . . ]