User manual SAMSUNG LT15N13W OPEN SOURCE GUIDE (VER.1.1)

[. . . ] It is dangerous to make any kind of contact with any inside part of this product. This symbol alerts you that important literature concerning operation and maintenance has been included with this product. Note to CATV system installer: This reminder is provided to call CATV system installer's attention to Article 820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. Caution: FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may void the user's authority to operate it. Caution: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug. [. . . ] After the hour is entered, press the VOL + button. 4 Press the VOL + button again. Press the CH L or CH M buttons repeatedly until the correct minutes appear. After the minutes are entered, press the VOL + button. Press the MENU button to exit. When selecting the hours, be sure to select the proper time of day (AM or PM). You can change the hours by pressing the CH L or CH M buttons repeatedly (or by holding down either of these buttons). The time will appear every time you press the Display button. M ENG 3. 9 O P E R AT I O N Customizing the Picture You can use the on-screen menus to change the contrast, brightness, sharpness, color, tint and color tone according to personal preference. (Alternatively, you can use one of the "automatic" settings. See next page. ) 1 Press the MENU button to display the menu. Press the VOL + button to display the Picture menu. 2 Press the CH M or CH L buttons to select a particular item. When Color Tone is selected you can choose between "Normal", "Warm", or "Cool" according to personal preference. M 3 Press the VOL + or VOL ­ buttons to increase or decrease the value of a particular item. For example, if you select "Contrast, " pressing VOL + increases it. Press the MENU button to exit. ENG 3. 10 O P E R AT I O N Using Automatic Picture Settings Your TV has two automatic picture settings ("Standard", "Mild" and "Dynamic") that are preset at the factory. Press the CH M button to select "Channel", then press the VOL + button. 2 Press the CH M button to select "LNA. " 3 Press the VOL + or VOL button to set LNA "On. " Press the MENU button to exit. Pressing VOL - or VOL + will alternate between "On" and "Off. " M ENG 4. 2 S P E C I A L F E AT U R E S Setting the Blue Screen Mode If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the poor picture, you must set the "Blue screen" mode to "Off". 1 Press the MENU button to display the menu. Press the CH M button to select "Function", then press the VOL + button. 2 Press the CH M button to select "Blue Screen. " 3 Press the VOL + or VOL buttons to set Blue Screen "On". Press the MENU button to exit. Pressing the VOL- or VOL+ buttons will alternate between "On" and "Off". M ENG 4. 3 S P E C I A L F E AT U R E S Changing the Screen Size (DVD/DTV) 1 Press the P. SIZE button to change the screen size. · · Normal: Sets the picture to 4:3 normal mode. Zoom: Magnifies the size of the picture on screen. Note: P . Size works in DVD/DTV mode. Freezing the Picture 1 Press the STILL button to freeze the main picture. · Not available if V-Chip is turned on. · Normal sound will still be heard. Press again to cancel. ENG 4. 4 S P E C I A L F E AT U R E S Special Sound Options Setting Multi-channel Soundtrack (MTS) When MTS is set to "Auto", MTS will be set automatically to "Mono" or "Stereo", according to the signal transmitted from the broadcasting company. If a channel is selected in an area where reception is poor, the sound might be distorted. When this occurs, set MTS Setting to "Manual" and MTS to "Mono". 1 Press the MENU button to display the menu. Press the CHM button to select "Sound", then press the VOL + button 2 Press the CHM button five times to select "MTS Setting". 3 Press the VOL + button repeatedly to select "Manual" or "Auto. " Press the MENU button to exit. ENG 4. 5 S P E C I A L F E AT U R E S Choosing a Multi-Channel Soundtrack (MTS) Depending on the particular program being broadcast, you can listen to stereo, mono, or a Separate Audio Program. [. . . ] Compare these values with the data in the Display Modes Timing Chart. Adjust the Coarse function and then adjust the Fine function. The TV is using its power management system. Move the computer's mouse or press a key on the keyboard. [. . . ]