User manual SAMSUNG LT17M24CU OPEN SOURCE GUIDE (VER.1.1)

[. . . ] (DVI-D terminal does not support PC. ) AV INPUT/OUTPUT Connect a Video signal from a camcorder or VCR. DVI-D AUDIO INPUT Connect to the audio output jack on your DVD/Set-top Box. ANT IN Connect to an antenna or to a cable TV system. PC VIDEO (D-SUB) INPUT Connect to the video output port on your PC. SUBWOOFER OUTPUT Connect to an active (powered) subwoofer. PC AUDIO (D-SUB) INPUT Connect to the audio output jack on your PC. ANYNET HEADPHONE JACK Connect a set of external headphones for private listening. COMPONENT IN 2 Connect component video/audio from a DVD/VCR/Set-top Box. English-1 POWER INPUT I N S TA L L AT I O N Connecting HDMI Supports connections between HDMI-connection-enabled AV devices (Set Top boxes, DVD players, AV receivers and digital TVs). 1 Connect HDMI cable from the TV to the input terminal of the HDMI device. What is HDMI? [. . . ] - HDMI, or high-definition multimedia interface, is a next-generation interface that enables the transmission of digital audio and video signals using a single cable without compression. - HDMI allows multiple channels of digital audio (5. 1 channels). The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP(High Definition Content Protection) coding feature installed, and supports multi - channel digital audio. How to connect Core Core provided reduces EMI(E1ectromagnetic Interference) noises from electrical or electronic products and prevents magnetic impact from ambient environment. After connecting AV cable of TV or Component cable, install Core as shown in the picture. English-2 I N S TA L L AT I O N Connecting a VCR These instructions assume that you have already connected your TV to an antenna or a cable TV system . Skip step 1 if you have not yet connected to an antenna or a cable system. 1 Unplug the cable or antenna from the back of the TV. 2 Connect the cable or antenna to the ANT IN terminal on the back of the VCR. 3 Connect a coaxial cable between the ANT OUT terminal on the VCR and the antenna terminal on the TV. AV OUT A coaxial cable is usually included with a VCR. The screen must be adjusted on the source(Set-top box). 4. Each external input source device has a different back panel configuration. English-4 I N S TA L L AT I O N Connecting a DVD Player The rear panel jacks on your TV make it easy to connect a DVD player to your TV. 1 Connect a set of audio cables between the COMPONENT1 or COMPONENT2 L, R AUDIO INPUT jacks on the TV and the AUDIO OUT jacks on the DVD player. 2 Connect a video cable between the COMPONENT1 or COMPONENT2 (Y, PB, PR) jacks on the TV and the Y, PB, PR jacks on the DVD player. Note: For an explanation of Component video, see your DVD player owner's manual. * Each external input source device has a different back panel configuration. Connecting a Digital TV Set-Top Box The connections for a typical set-top box are shown below. 1 Connect a set of audio cables between the L, R COMPONENT1 or COMPONENT2 AUDIO INPUT jacks on the TV and the AUDIO OUT jacks on the Set-Top Box. 2 Connect a video cable between the COMPONENT1 or COMPONENT2 (Y, PB, PR) jacks on the TV and the Y, PB, PR jacks on the Set-Top Box. Note: For an explanation of Component video, see your Set-Top Box owner's manual. * Each external input source device has a different back panel configuration. English-5 I N S TA L L AT I O N Connecting a PC Note: This figure shows the Standard Connector-jack panel. The actual configuration on your TV may be different. - Connect the D- Sub cable to "PC (PC IN)" on the rear of your set. [. . . ] The actual configuration on your TV may be different. - Connect the D- Sub cable to "PC (PC IN)" on the rear of your set. [. . . ]