User manual SAMSUNG LT17N23W OPEN SOURCE GUIDE (VER.1.1)

[. . . ] (DVI-D terminal does not support PC. ) S-VIDEO Connect an S-Video signal from a camcorder or VCR VIDEO/AUDIO INPUT Connect a Video signal from a camcorder or VCR. PC VIDEO (D-SUB) INPUT Connect to the video output port on your PC. PC AUDIO (D-SUB) INPUT Connect to the audio output jack on your PC. ANT IN Connect to an antenna or to a cable TV system. DVI-D AUDIO INPUT Connect to the audio output jack on your DVD/Set-top Box. SUBWOOFER OUTPUT Connect to an active (powered) subwoofer. COMPONENT IN 1 Connect component video/audio from a DVD/VCR/Set-top Box. HEADPHONE JACK Connect a set of external headphones for private listening. COMPONENT IN 2 Connect component video/audio from a DVD/VCR/Set-top Box. English-1 POWER INPUT I N S TA L L AT I O N Connecting a VCR These instructions assume that you have already connected your TV to an antenna or a cable TV system . [. . . ] (If not, check your local electronics store). 4 Connect a set of audio cables between the AUDIO OUT jacks on the VCR and the AUDIO jacks on the TV. If you have a "mono" (non-stereo) VCR, use the Y-connector (not supplied) to hook up to the left and right audio input jacks of the TV. If your VCR is stereo, you must connect two cables. 5 Connect a video cable between the VIDEO OUT jack on the VCR and the VIDEO jack on the TV. Follow the instructions in "Viewing a VCR or Camcorder Tape" to view your VCR tape. * Each external input source device has a different back panel configuration. English-2 I N S TA L L AT I O N Connecting an S-VHS VCR Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR. (This connection delivers a better picture as compared to a standard VHS VCR. ) 1 To begin, follow steps 1­3 in the previous section to connect the antenna or cable to your VCR and your TV. 2 Connect a set of audio cables between the AUDIO OUT jacks on the VCR and the AUDIO INPUT jacks on the TV. 3 Connect an S-video cable between the S-VIDEO OUT jack on the VCR and the S-VIDEO INPUT jack on the TV. An S-video cable is usually included with an S-VHS VCR. 4. Each external input source device has a different back panel configuration. English-3 I N S TA L L AT I O N Connecting a DVD Player The rear panel jacks on your TV make it easy to connect a DVD player to your TV. 1 Connect a set of audio cables between the COMPONENT1 or COMPONENT2, L, R AUDIO INPUT jacks on the TV and the AUDIO OUT jacks on the DVD player. 2 Connect a video cable between the COMPONENT1 or COMPONENT2 (Y, PB, PR) jacks on the TV and the Y, PB, PR jacks on the DVD player. Note: For an explanation of Component video, see your DVD player owner's manual. * Each external input source device has a different back panel configuration. Connecting a Digital TV Set-Top Box The connections for a typical set-top box are shown below. 1 Connect a set of audio cables between the L, R COMPONENT1 or COMPONENT2 AUDIO INPUT jacks on the TV and the AUDIO OUT jacks on the Set-Top Box. 2 Connect a video cable between the COMPONENT1 or COMPONENT2 (Y, PB, PR) jacks on the TV and the Y, PB, PR jacks on the Set-Top Box. Note: For an explanation of Component video, see your Set-Top Box owner's manual. * Each external input source device has a different back panel configuration. English-4 I N S TA L L AT I O N Connecting a PC Note: This figure shows the Standard Connector-jack panel. The actual configuration on your TV may be different, depending on the model. - Connect the D- Sub cable to "PC (PC IN)" on the rear of your set. [. . . ] The actual configuration on your TV may be different, depending on the model. - Connect the D- Sub cable to "PC (PC IN)" on the rear of your set. [. . . ]