User manual SAMSUNG LT32A23W OPEN SOURCE GUIDE (VER.1.1)

[. . . ] Skip step 1 if you have not yet connected to an antenna or a cable system. 1 Unplug the cable or antenna from the back of the TV. 2 Connect the cable or antenna to the ANTENNA IN terminal on the back of the VCR. 3 Connect a coaxial cable between the ANTENNA OUT terminal on the VCR and the antenna terminal on the TV. A coaxial cable is usually included with a VCR. [. . . ] If your VCR is stereo, you must connect two cables. 5 Connect a video cable between the VIDEO OUT jack on the VCR and the VIDEO jack on the TV. Follow the instructions in "Viewing a VCR or Camcorder Tape" to view your VCR tape. * Each external input source device has a different back panel configuration. English-2 victoryia 01-14 1/12/04 1:51 AM Page 12 I N S TA L L AT I O N Connecting an S-VHS VCR Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR. (This connection delivers a better picture as compared to a standard VHS VCR). 1 To begin, follow steps 1­3 in the previous section to connect the antenna or cable to your VCR and your TV. 2 Connect a set of audio cables between the AUDIO OUT jacks on the VCR and the AUDIO INPUT jacks on the TV. 3 Connect an S-video cable between the S-VIDEO OUT jack on the VCR and the S-VIDEO INPUT jack on the TV. An S-video cable is usually included with an S-VHS VCR. (If not, check your local electronics store). * Each external input source device has a different back panel configuration. English-3 victoryia 01-14 1/12/04 1:51 AM Page 13 I N S TA L L AT I O N Connecting a DVD Player The rear panel jacks on your TV make it easy to connect a DVD player to your TV. 1 Connect a set of audio cables between the L, R AUDIO INPUT jacks on the TV and the AUDIO OUT jacks on the DVD player. 2 Connect a video cable between the COMPONENT1 (Y, Pb, Pr) jacks on the TV and the Y, Pb, Pr jacks on the DVD player. Note: For an explanation of Component video, see your DVD player owner's manual. * Each external input source device has a different back panel configuration. Connecting a DVD Player or Set-Top Box to the TV with a DVI-D Cable 1 Connect a DVI-D cable between the DVI-I INPUT connector on the TV and the DVI connector on the DVD player/ Set-Top BOX. 2 Connect a set of audio cables between the PC AUDIO INPUT jack on the TV and the AUDIO OUTPUT jacks on the DVD player/ Set-Top BOX. Note: If you are using a DVI-D cable to connect 1. Each external input Source device has a different back panel configuration. English-4 victoryia 01-14 1/10/04 1:03 AM Page 14 INSTALLATION Connecting a PC Note: This figure shows the Standard Connector-jack panel. The actual configuration on your TV may be different, depending on the model. TV rear panel PC rear PC VIDEO INPUT (24-pin DVI) (Optional) PC SOUND INPUT (Optional) · PC AUDIO INPUT Connect these to the audio-output jacks on your PC. · PC VIDEO INPUT Connect to the video output port on your PC. * Each external input source device has a different back panel configuration. English-5 victoryia 62-70 1/10/04 1:05 AM Page 61 How to connect the cables and stand base 1 Remove the cover as shown in the picture. 2 Connect the cables as shown in the picture. 3 Replace the cover. 4 Attach the stand to the TV set as shown in the picture. Note : The curved side of the stand base should be placed toward the back of the TV set as shown in the above figure. Do NOT lift the TV set by the stand. [. . . ] · PC VIDEO INPUT Connect to the video output port on your PC. * Each external input source device has a different back panel configuration. English-5 victoryia 62-70 1/10/04 1:05 AM Page 61 How to connect the cables and stand base 1 Remove the cover as shown in the picture. 2 Connect the cables as shown in the picture. 3 Replace the cover. 4 Attach the stand to the TV set as shown in the picture. Note : The curved side of the stand base should be placed toward the back of the TV set as shown in the above figure. Do NOT lift the TV set by the stand. [. . . ]