User manual SAMSUNG LT40A13W OPEN SOURCE GUIDE (VER.1.1)

[. . . ] (If not, check your local electronics store). 4 Connect a set of audio cables between the AUDIO OUT jacks on the VCR and the AUDIO jacks on the TV. If you have a "mono" (non-stereo) VCR, use the Y-connector (not supplied) to hook up to the left and right audio input jacks of the TV. If your VCR is stereo, you must connect two cables. 5 Connect a video cable between the VIDEO OUT jack on the VCR and the VIDEO jack on the TV. Follow the instructions in "Viewing a VCR or Camcorder Tape" to view your VCR tape. * Each external input source device has a different back panel configuration. English-2 BN68-00633A-06Eng 1. qxd. q 5/12/04 6:31 PM Page 11 I N S TA L L AT I O N Connecting an S-VHS VCR Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR. [. . . ] (If not, check your local electronics store. ) * Each external input source device has a different back panel configuration. English-3 BN68-00633A-06Eng 1. qxd. q 5/12/04 6:31 PM Page 12 INSTALLATION Connecting a DVD Player The rear panel jacks on your TV make it easy to connect a DVD player to your TV. 1 Connect a set of audio cables between the L, R AUDIO INPUT jacks on the TV and the AUDIO OUT jacks on the DVD player. 2 Connect a video cable between the COMPONENT (Y, Pb, Pr) jacks on the TV and the Y, Pb, Pr jacks on the DVD player. Note : For an explanation of Component video, see your DVD player owner's manual. The component terminal of this set only supports 480i/480p resolution. * Each external input source device has a different back panel configuration. English-4 BN68-00633A-06Eng 4. qxd. q 5/12/04 6:33 PM Page 56 APPENDIX Installing the Wall Mount Kit Note : This installation is to be used when attaching the wall mount to a concrete wall. When attaching to other building materials, please contact your nearest dealer. Components Please use provided components or parts to install the Wall Mount Kit. Bracket Anchors : 3EA Screws : 3EA Installation Guide How to assemble the Wall Mount Kit 1 Mark the location of hole on the wall using installation guide. Make over 35mm- depth- hole on the marked location using 5. 0-diameter drill. Connect bracket to the wall with screws after fitting anchors into the bracket holes. Note : If the bracket is not firmly fixed to the wall, LCD TV can fall off. 2 After placing LCD TV on cushion or other soft material, turn over LCD TV in the direction of arrow while grabbing bottom of the stand. 3 When using LCD TV in stand-based form, place the product on a cushion or other soft materials. Then turn over stand following the arrow direction below only after pressing button on the connected part where LCD TV is attached to stand. Connect bracket to the wall with screws after fitting anchors into the bracket holes. Note : If the bracket is not firmly fixed to the wall, LCD TV can fall off. 2 You may use LCD TV right after fixing it to the wall since stand is wrapped already turned over as shown in the picture 3 When using LCD TV in stand-based form, place the product on a cushion or other soft materials. Then turn over stand following the arrow direction below only after pressing button on the connected part where LCD TV is attached to stand. (Turn over stand in the opposite direction after pressing button when using LCD TV in wall-mounted form as well. ) English-7 BN68-00633A-06Eng 4. qxd. q 5/12/04 6:34 PM Page 59 APPENDIX Installing the Wall Mount Kit 4 Adjust LCD TV to the hook on the bracket and move in the direction of the arrow(Left) so that LCD TV can be completely fixed to the bracket. When bracket is assembled on the wall How to hang monitor up on a hook When installation is completed 5 6 Remove Installation Guide after completing setup of LCD TV on the wall. Push the LCD TV up and shift to the right to detach it from bracket. When moving or transferring to other areas, reverse No. 4 procedure so as to disconnect LCD TV with ease. How to adjust an angle (1) Angle adjustment section of general stand-besd LCD TV (2) Angle abjustment section while converting the form (1->3, 3->1) (3) Angle adjustment section of wall-mounted LCD TV Picture (1) shows the adjustment angle (0°~ 13°) when you use LCD TV in its general form (stand-based LCD TV). [. . . ] 4 procedure so as to disconnect LCD TV with ease. How to adjust an angle (1) Angle adjustment section of general stand-besd LCD TV (2) Angle abjustment section while converting the form (1->3, 3->1) (3) Angle adjustment section of wall-mounted LCD TV Picture (1) shows the adjustment angle (0°~ 13°) when you use LCD TV in its general form (stand-based LCD TV). Excessive tilting can turn LCD TV over which might cause damage to LCD TV. [. . . ]