User manual SAMSUNG MAX-DN83 INTRODUCTION

[. . . ] THREE-CD CHANGER MINI-COMPACT SYSTEM DVD / VIDEO-CD / CD MAX-DN85/DN87 Instruction Manual Safety Warnings GB CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT PRODUCTO LASER CLASE 1 Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. CAUTION-INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED, AVOID EXPOSURE TO BEAM. This symbol indicates that dangerous voltage which can cause electric shock is present inside this unit. This symbol alerts you to important operating and maintenance instructions accompanying the unit. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. [. . . ] This enables the simple adjustment of sound levels, to achieve, at the listening position, the same apparent loudness from each channel. Use the remote control. Dolby Surround modes Press the Dolby Surround button. PRO-Logic is selected, and the playback sound has the Dolby Surround effect. To cancel Dolby Surround mode Press the Dolby Surround button repeatedly until OFF is displayed. Open/Close Mute 1 2 Press the Dolby Surround button. Result: " PRO-LOGIC" appears on the displayed. 1 4 7 Disc Skip 2 5 8 10/0 3 DSP/EQ Dolby Surround Press the Test Tone button. A noise signal is sent to each channel in turn in the following sequence. 6 S. Bass Power Sound 9 Clear Program Repeat L CNTR R REAR (L : Left Speaker, CNTR : Center Speaker, R : Right Speaker, REAR : Rear Speaker) When playing DVD, if an Audio is Dolby Digital, it can not be operated. When being connected to headphones and microphone, this function cannot be operated. 3 4 Press the Test Tone button again to stop the noise signal. To change the sound levels or delay time after adjusting the balance with the noise sequencer. While L, R, CNTR, REAR is displayed, press the UP/DOWN Additional Dolby Surround modes In addition to the PRO-Logic mode, this unit is also equipped with the 3 STEREO modes. PRO-Logic : Use this mode when rear speakers are connected. The center channel signals are output through the left and right speakers. 3 STEREO : Use this mode when no rear speakers are connected. This mode reproduces rear sounds through the front speakers. PRO-Logic 3 STEREO OFF ( / ) button. Press the Speaker Mode button. While CNTR, REAR, DELAY TIME is displayed, press the UP/DOWN ( / ) button. ­ CNTR : Large/Small/None ­ REAR : USE/None ­ DELAY TIME : 15/20/25/30 MS When the Dolby surround system is on, this function can be operated. Open/Close Mute 1 2 5 8 10/0 3 DSP/EQ Dolby Surround Depending on the sound source or listening conditions, a surround effect may not be obtained even when the Dolby Surround is on. The full Dolby Surround effect cannot be obtained when using softDOLBY SURROUND ware without mark. In this case, use the DSP system instead. P R O L O G I C 4 7 Disc Skip 6 S. Bass 9 Clear 1 Power Sound Program Repeat DVD/CD DECK Deck 1/2 Band + On/Standby Volume Tuning Mode Open/Close Mute 1 4 7 Disc Skip 2 5 8 10/0 3 DSP/EQ Dolby Surround 6 S. Bass Power Sound Timer On/Off Volume ­ 9 Clear Program Repeat 4 Speaker Mode Sound Edit Angle Zoom Audio Go To Sleep Test Tone DVD/CD 4 Step Menu Display Set up AUX DECK 2, 3 Title Enter 4 Return Sub Title Deck 1/2 Band + Volume Tuning Mode Volume ­ 22 Dolby Surround (Cont'd) To set the delay time When 5. 1 Channel Surround Sound is played, you can enjoy the best sound if the distance between you and each speaker is the same. You can set Delay Time in the Center/Rear Speaker to customize the sound to the acoustics of your room. Setting Center Speaker If the distance of Dc is equal to or longer than the distance of Df in the figure, set the mode as 0ms. Otherwise, change the setting according to the table on the table. Setting Rear Speakers If the distance of Df is equal to the distance of Ds in the figure, set the mode as 0ms. Otherwise, change the setting according to the table. Dolby Surround (Cont'd) GB Speaker Setting Methods (A)=Df-Dc Distance of (A) 50 100 150 200 Value(ms) 1. 3 2. 6 3. 9 5. 3 Front Speakers (B)=Df-Ds Distance of (B) 200 400 600 Value(ms) 5. 3 10. 6 15. 9 Set the front speakers so that their tweeters (high-range) are aligned at about ear level and at a horizontal angle of 45° to the prime listening position. [. . . ] The DVD's software doesn't support the feature (e. g. , angles). The feature is not available at the moment. You've requested a title or chapter number or search time that is out of range. · Some of the functions selected in the Setup Menu may not work properly if the disc is not encoded with the corresponding function. [. . . ]