User manual SAMSUNG MCM-A100

[. . . ] · Never attempt to install the air conditioning system or to move the function controller by yourself. WARNING Do not attempt to install or repair this function controller by yourself. This function controller contains no user-serviceable parts. Always consult authorized service personnel for repairs. When moving, consult authorized service personnel for Ensure that the wall is strong enough to support the disconnection and installation of the function controller. supply. Must install the function controller with rated power In the event of a malfunction (burning smell, etc. ), immediately stop operation, turn off the electrical breaker, and consult authorized service personnel. CAUTION Do not use inflammable gases near the function controller. Do not spill water into the function controller. Do not operate the function controller with wet hands. Do not install the function controller in a location where it will come into contact with the combustible gases, machine oil, sulphide gas, etc. [. . . ] AIRING YOUR ROOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ADJUSTING THE AIR FLOW DIRECTION(EXCEPT DUCT TYPE) . . . . . . . 4 5 6 7 8 10 12 14 15 E-3 ENGLISH View of the Function Controller The function controller is an additional controller which is used with the centralized controller. Operating mode Removing frost indicator (Except Cooling Only Models) Centralized controller indicator Communication error indicator Room number display Test indicator Temperature adjustment buttons Indoor unit selection button Temperature setting Fan speed Air flow direction Filter Sign indicator On/Off & Timer Set/Cancel button On/Off indicator Fan speed adjustment button Swing button (Except Duct Type) Test button Filter Reset button Mode selection button Note controller will display the FILTER SIGN indicator when the time to clean the air filter. Duct type air conditioner does not have function of adjusting air flow direction. Therefore, the function is not operated even if you press the swing button. Test button is for your installation specialist. After cleaning the air filter, press the filter reset button. Then the function E-4 Getting Started You have just purchased a function controller and it has been installed by your installation specialist. Your user's manual contains much valuable information on using your function controller. Please take time to read as it will help you take full advantage of the unit's features. In the main part of the document, you will find a series of step-by-step procedures for each function available. The illustrations in the step-by-step procedures use three different symbols: PRESS PUSH HOLD DOWN E-5 ENGLISH Selecting the Indoor Unit You can control a specific indoor unit from the function controller. 1 Select an indoor unit you want to control by pressing button. Result: E ach time you press button, the room number is increased by 1, and each time you press button, the room number is decreased by 1 from 0~15. 2 Turn the air conditioner on by pressing Result: comes on. (ON/OFF) button. The On/Off indicator on the function controller The air conditioner runs in the mode selected when the unit was last used. 3 Select an appropriate operating mode by pressing Mode button. Result: Note The air conditioner runs in the selected mode. For further details on operating modes, refer to page 7~15. E-6 Selecting the Automatic Operating Mode ENGLISH In the Automatic mode, the room temperature and the fan speed are controlled automatically. 1 If necessary, press Result: (ON/OFF) button. The On/Off indicator on the function controller comes on. The air conditioner runs in the mode selected when the unit was last used. Caution The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped lt will start up normally after three minutes. 2 To select the AUTO mode, press the Mode button until displayed at the top of the function controller. Result: Note The air conditioner runs in AUTO mode. You can change modes at any time. is 3 To adjust the temperature, press the Temperature buttons one or more times until the required temperature is displayed. Possible temperatures are between 18°C(65°F) and 30°C(86°F) inclusive. Result: Each time you press Temperature buttons: - The temperature is adjusted by 1°C(1°F). The air conditioner starts cooling, provided that the room temperature is than the selected temperature. - The quantity of air is adjusted automatically. E-7 Cooling Your Room You must select the COOL mode if you wish to adjust the : Cooling temperature Fan speed when cooling 1 If necessary, press Result: (ON/OFF) button. The On/Off indicator on the function controller comes on. The air conditioner runs in the mode selected when the unit was last used. Caution The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped lt will start up normally after three minutes. 2 To select the COOL mode, press the Mode button until displayed at the top of the function controller. Result: Note The air conditioner runs in COOL mode. You can change modes at any time. is E-8 3 To adjust the temperature, press the Temperature buttons one or more times until the required temperature is displayed. [. . . ] The quantity of air is adjusted automatically. 4 To control the direction of the air flow, refer to page 15. E-13 ENGLISH Airing Your Room If the atmosphere in your room is stale, you can air it using the FAN feature. 1 If necessary, press Result: (ON/OFF) button. The On/Off indicator on the function controller comes on. The air conditioner runs in the mode selected when the unit was last used. Caution The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped lt will start up normally after three minutes. 2 To select the FAN mode, press the Mode button until displayed at the top of the function controller. Result: Note The air conditioner runs in FAN mode. You can change modes at any time. is 3 Select the fan speed by pressing the Fan button one or more times until the intended value is displayed : Low Medium High 4 To control the direction of the air flow, refer to page 15. E-14 Adjusting the Air Flow Direction (Except Duct Type) ENGLISH Depending on the position of the indoor unit, you can adjust the position of the air flow blade, thus increasing the efficiency of the air conditioner. 1 Press the Swing button. Result: The blade is moving up and down. [. . . ]