User manual SAMSUNG MH026FNEA

[. . . ] Contents PREPARATION Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Name of Each Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Control ­ Buttons and Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inserting the Remote Control Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Sleep may be disturbed if the mode is set for too short or too long a time because the temperature changes are set to an 8-hour cycle. mode is set for less than 4 hours, the operation will stop at the set time. mode is set for over 5 hours, the last hour will run in Waking Up stage before · Recommended set temperature is between 25°C~27°C for cooling and 21°C~23°C for heating. Cool mode Temp. Set temperature When the 8-hour cycle completes, this section repeats. When the 8-hour cycle completes, this section repeats. Set temperature Time(hr. ) E-19 FJM_Neo_FORTE_Inv_28925A_IB_E. indd 19 2007-12-3 19:10:18 Selecting the Turbo Function You can select the Turbo Function if you want to cool or heat your room as quickly as possible. The Turbo function operates for 30 minutes with the maximum settings before returning automatically to the mode and temperature previously selected. 1 Press the Result: (On/Off) button. The operation indicator on the indoor unit lights up. The air conditioner starts up in the mode you selected last. The indoor unit beeps. 2 Press the Result: button. The temperature and fan settings are adjusted automatically. The air conditioner cools or heats the room as quickly as possible. After 30 minutes, the air conditioner is reset automatically to the previous setting. You can select the Turbo function in Auto, Cool and Heat mode. If you select this function in Dry or Fan mode, the mode changes to Auto mode. 3 Press the button again to stop the Turbo Function before the end of the 30-minute period. Result: The air conditioner is reset automatically to the previous setting. 4 To control the airflow direction, refer to page 21. E-20 FJM_Neo_FORTE_Inv_28925A_IB_E. indd 20 2007-12-3 19:10:19 Adjusting the Airflow Direction Vertically ENGLISH You can adjust the airflow direction vertically. The outer airflow blade moves up and down to increase the efficiency of the cooling or heating operation. 1 Press the Result: button until the required direction is set. The outer blade is adjusted vertically. 2 Press the button again to move the blade up and down automatically during operation. 3 Press the Note button again to stop the blade moving up and down. set to the default position. Adjusting the Airflow Direction Horizontally You can adjust airflow direction horizontally manually. The inner blades with small fins move the air in the desired direction. 1 Adjust the inner blades by moving them left or right. Make sure do not touch the inner blades during operation. It may cause injury on your fingers. E-21 FJM_Neo_FORTE_Inv_28925A_IB_E. indd 21 2007-12-3 19:10:21 Setting the On Timer You can set the On Timer to turn on the air conditioner automatically at the appointed time within a range of 30 minutes to 24 hours. 1 Press the button until the desired time is displayed to set the On Timer. You can set the time between 0. 5 hour and 24 hours. 2 Press the Result: button to complete the setting. [. . . ] Check if the air filter is blocked by dirt. Check if the there is cover on the outdoor unit or any obstacle. Check if you installed the air conditioner under direct sunlight. Check if you turn on the air conditioner just now. [. . . ]