User manual SAMSUNG MH26AP2X-XFO

[. . . ] Indoor unit MH18AP1(P2)-09 MH19AP1(P2)-07 MH19AP1(P2)-12 MH24AP1(P2)-12 MH26AP1(P2)-07 MH26AP1(P2)-12 AD18P1(P2)E09 AD19P1(P2)E07 AD19P1(P2)E12 AD24P1(P2)E12 AD26P1(P2)E07 AD26P1(P2)E12 Outdoor unit MH18AP1(P2)X MH19AP1(P2)X MH24AP1(P2)X MH26AP1(P2)X UD19P1(P2)E2 UD24P1(P2)E2 UD26P1(P2)E3 MULTI-SPLIT TYPE ROOM AIR CONDITIONER ( Cool and Heat ) ACONDICIONADOR DE AIRE DOMSTICO SISTEMA MULTI SPLIT ( Refrigeracin y Calefaccin ) CLIMATISEUR DE TYPE MULTIPLE ( Refroidissement et Chauffage ) CONDIZIONATORE D'ARIA PER PI AMBIENTI AD UNIT SEPARATE ( Raffreddamento e Riscaldamento ) AR CONDICIONADO MULTI SPLIT ( Refrigerao e Aquecimento ) RAUMKLIMAGERT IN MEHRFACH GETEILTER AUSFHRUNG ( Khlen und Wrmen ) IAIPOYMENO KIMATITMTIKO MATIOY ( ~ η ̷~ ) E S F I P D G DB98-15934A(6) EHNIKA DEUTSCH PORTUGUS ITALIANO UD18P1(P2)E2 FRANAIS ESPAOL OWNER'S INSTRUCTIONS MANUAL DE INSTRUCCIONES MANUEL D'UTILISATION ISTRUZIONI PER L'USO MANUAL DE INSTRUES GEBRAUCHSANWEISUNG TM TM ENGLISH Register your product at www. samsung. com/global/register Safety Precautions The following safety precautions must be taken when using your air conditioner. Disconnect all remote electric power supplies before servicing, installing or cleaning. This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. x Users of this product are cautioned not to attempt repair of this product at their own discretion. [. . . ] The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped It will start up normally after three minutes. IMPORTANT 2 If the is not displayed at the top of the remote control, press the button on the remote control one or more times until it appears. Result: Note x The indoor unit beeps each time you press the x The air conditioner runs in DRY mode. button. 3 To adjust the temperature, press the button one or more times until the required temperature is displayed. Possible temperatures are between 18C and 30C inclusive. Result: x Each time you press the button: - The temperature is adjusted by 1C - The indoor unit beeps x The air conditioner starts removing the excess humidity; the quantity of air is adjusted automatically. 4 To control the direction of the air flow, refer to page 15. E-13 Airing Your Room If the atmosphere in your room is stale, you can air the room using the Fan feature. 1 If necessary, press the Result: (On/Off) button. x The operation indicator on the indoor unit lights up. x The air conditioner starts up in the mode selected when the unit was last used. x The indoor unit beeps. 2 If the is not displayed at the top of the remote control, press the button on the remote control one or more times until it appears. Result: x The indoor unit beeps each time you press the x The air conditioner runs in FAN mode. button. Note 3 Select the fan speed by pressing the until the required setting is displayed: Low Medium High Result: Each time you press the button one or more times button, the indoor unit beeps. 4 To control the direction of the air flow, refer to page 15. E-14 Adjusting the Air Flow Direction Vertically ENGLISH Depending on the position of the indoor unit on the wall of your room, you can adjust the position of the outer air flow blade on the bottom of the unit, thus increasing the efficiency of the air conditioner. 1 Press the Result: button one or more times as required. Cooling Heating Adjust the blade to face. . . Downwards. RECOMMENDATION 2 If you want the blade to move up and down automatically when the air conditioner is operating, press the Result: button. The blade move up and down, around the base position set. 3 To stop the blade moving up and down, press the button again. Note If you switch the air conditioner. . . Set to the initial position powered. Adjusting the Air Flow Direction Horizontally There are two sets of inner air flow blades. Just as the outer air flow blade can be adjusted vertically, the inner blades can be adjusted horizontally. 1 Adjust each set of inner blades to the required position, by pushing or pulling them sideways. E-15 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time. You can set the period of time from 30 minutes to 24 hours. 1 To set the operating time, press the button one or more times until the required time is displayed. Possible time is between 0. 5 hour and 24 hours inclusive. 2 Press the Result: (Set/Cancel) button to complete the setting. x Blinking of the timer indicator stops. x The selected mode and the temperature on the display disappear after 10 seconds. [. . . ] Explanation/Solution x Check that the breaker used for the air conditioner is switched on. x Check that the operation indicator on the indoor unit is on; if necessary press the (On/Off) button on the remote control. x Check whether the Timer indicator on the indoor unit is switched on. If so: - Wait until the switch-on time is reached and the air conditioner starts up automatically - Cancel the timer (see pages 16 and 17 for further details) x Check that there are no obstacles between you and the indoor unit. [. . . ]