User manual SAMSUNG MM-ZJ9

[. . . ] 5CD CHANGER MICRO COMPONENT MP3-CD/CD-R/RW PLAYBACK MM-ZJ9 Instruction Manual 1 Safety Warnings GB CLASS 1 LASER PRODUCT CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT PRODUCTO LASER CLASE 1 This Compact Disc player is classified as a CLASS 1 LASER product. Use of controls adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. CAUTION-INVISIBLE LASER RADIATION WHEN OPEN AND INTER LOCKS DEFEATED, AVOID EXPOSURE TO BEAM. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. [. . . ] If this happens, use the manual search mode. If you do not want to store the radio station found, revert to Step 4 and search for another station. Otherwise: a Press the PROGRAM/SET button. Result: The PROG is displayed for a few seconds. b Press the or buttons on the front panel or or buttons on the remote control to assign a program number . c Press the PROGRAM/SET button to store the radio station. Result: PROG is no longer displayed and the station is stored. 3 3 3 5 Improving Radio Reception You can improve the quality of radio reception by: Rotating the FM or AM(MW) aerial If reception from a specific FM radio station is poor, press the MO/ST button. to switch from stereo mode to MONO The quality of the sound will be improved. 6 To store any other radio frequencies required, repeat Steps 3 to 5. The PROGRAM function can be used to assign a new station to an existing program number. 1 2 45 5 3 45 45 45 3 2 15 Listening to a Cassette GB Always treat your cassettes with care; refer, if necessary, to the section entitled "Precautions When Using Audio Cassettes" on page 22. Tape Counter When playing a cassette, a counter is displayed to enable you to take note of the counter value at the start of each track and thus start playback at the beginning of the track to which you wish to listen. 1 2 3 Switch the system on by pressing the ( Press the TAPE ( ) button. ) button. Open the cassette deck by pushing on the corner of the cover marked the PUSH EJECT ( ) button until you hear a click and then releasing it. Insert the pre-recorded cassette with the open edge of the tape facing downwards. Close the deck by pushing on it until it clicks into place. Side A Side B Result: The cassette starts playing. Rewind the cassette Fast-forward the cassette Press . . . TAPE ( TAPE ( The counter is only displayed when a cassette is being played. Before starting to record a cassette for which you wish to take note of the counter values at the beginning of each track, reset the counter by pressing the COUNTER RESET button. 4 5 ) button once. button. When you have finished playback, press the Selecting the Cassette Playback Mode Your micro component system has three cassette playback modes which enable you to listen to both sides of a cassette automatically. Press the REV. MODE button until the appropriate symbol is displayed. 2, 5 1 When the display indicates. . . The micro component system plays back. . . 6 7 6 One side of the selected cassette and then stops. The other side of the cassette and then stops. Both sides of the cassette indefinitely until you press stop. 16 Recording a Compact Disc You can record a compact disc on a cassette in two different ways: Synchronised recording Direct recording 3 GB Use the DISC button to open the CD tray you want and insert a CD in the tray. Press the OPEN/CLOSE ( ) button to open the CD door. ) button to close Synchronised recording This feature enables you to synchronize the start of the recording with the start of the disc or track of your choice. Insert a CD and press the OPEN/CLOSE ( the CD door. 4 5 Press the MP3-CD/CD (/») button. [. . . ] · The timer has been stopped by pressing TIMER ON/OFF. · Press the TUNING MODE button for 5 seconds in power `OFF'(standby), then it is returned the original position (RESET) · The CD function has not been selected. · The disc has been inserted face down or is either dirty or scratched. · The laser sensor is dirty or dusty. [. . . ]