User manual SAMSUNG NP-R408P

[. . . ] R408 plus User Guide Contents Chapter 1. Getting Started Cautions Regarding OS Support Before You Start Safety Precautions Proper Posture During Computer Use Important Safety Information Replacement Parts and Accessories Regulatory Compliance Statements WEEE SYMBOL INFORMATION Basic Items Overview Front View Status Indicators Right View Left View Back View Bottom View Attaching the Battery Connect the AC adapter Turn on the computer Chapter 2. Using the computer 6 7 9 23 26 28 30 42 43 44 44 45 46 47 48 49 50 50 51 Keyboard Touchpad CD Drive (ODD, Optional) Multi Card Slot ExpressCard Slot Adjusting the Volume Inserting and Ejecting a CD 54 58 59 61 63 64 59 Chapter 3. Settings and Upgrade LCD Brightness Control BIOS Setup Entering the BIOS Setup The BIOS Setup Screen 66 67 67 68 Setting a Boot Password Changing the Boot Priority Upgrading Memory Battery Installing/Removing the Battery Charging the Battery Measuring the Remaining Battery Charge Extending the Battery Usage Time 70 72 73 75 75 76 76 77 Turn on the computer 50 Using Sleep Mode 52 Using the Security Lock Port 78 Chapter 4. [. . . ] If trouble is experienced with this equipment (Modem) for repair or warranty information, please contact your local distributor. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. The user must use the accessories and cables supplied by the manufacturer to get optimum performance from the product. This equipment cannot be used on public coin phone service provided by the telephone company. Connection to party line service is subject to state tariffs. The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be any number for which charges exceed local or long-distance transmission charges. ) In order to program this information into your fax machine, refer to your communications software user manual. Canada Unintentional Emitter per ICES-003 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada. Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limitesapplicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par Industrie Canada. The maximum allowed antenna gain for use with this device is 6dBi in order to comply with the E. I. R. P limit for the 5. 25- to 5. 35 and 5. 725 to 5. 85 GHz frequency range in point-to-point operation. As a general guideline, a separation of 20 cm (8 inches) between the wireless device and the body, for use of a wireless device near the body (this does not include extremities) is typical. This device should be used more than 20 cm (8 inches) from the body when wireless devices are on. The power output of the wireless device (or devices), which may be embedded in your notebook, is well below the RF exposure limits as set by Industry Canada. Intentional Emitter per RSS 210 Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2. 4GHz/5GHz Band, may be present (embedded) in your notebook system. This section is only applicable if these devices are present. Refer to the system label to verify the presence of wireless devices. Wireless devices that may be in your system are only qualified for use in Canada if an Industry Canada ID number is on the system label. When using IEEE 802. 11a wireless LAN, this product is restricted to indoor use due to its operation in the 5. 15to 5. 25-GHz frequency range. Industry Canada requires this product to be used indoors for the frequency range of 5. 15 GHz to 5. 25 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High power radar is allocated as the primary user of the 5. 25- to 5. 35-GHz and 5. 65 to 5. 85-GHz bands. These radar stations can cause interference with and/or damage to this device. This transmitter must not be collocated or operate in conjunction with any other antenna or transmitter except the installed Bluetooth transmitter. Operation of this device is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. To prevent radio interference to licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. [. . . ] For detailed setting information, ask your network administrator. Radio Specifications RF Band Supported Channels Device Standard Output Power 2. 4GHz, 5GHz Channels allowed per country. Transceiver MAX 10mW 11a mode : OFDM 11b mode : DSSS 11g mode : OFDM 11n mode : MIMO 11a mode** : MAX 54Mbps 11b mode : MAX 11Mbps 11g mode*** : MAX 54Mbps 11n mode**** : MAX 450Mbps, MAX 300Mbps Built-in Antenna Modulation Scheme Data Rate (Mbps)* Antenna Type * ** *** The data rate may differ from the real data transmission rate. 11a mode is only supported when it is connected to an IEEE802. 11a device (e. g. Access Point supporting IEEE802. 11a). 11g mode is supported only when you are connected to an IEEE 802. 11g device (e. g. [. . . ]