User manual SAMSUNG NP-R518-DS03

[. . . ] Getting Started Cautions Regarding OS Support Before You Start Safety Precautions Important Safety Information Replacement Parts and Accessories Regulatory Compliance Statements WEEE SYMBOL INFORMATION Basic Items Overview Front View Status Indicators Right View Left View Back View Bottom View Attaching the Battery Connect the AC adapter Turn on the computer 6 7 9 23 25 27 39 40 41 41 42 43 44 45 45 46 46 47 Chapter 3. Settings and Upgrade LCD Brightness Control BIOS Setup Entering the BIOS Setup The BIOS Setup Screen 62 63 63 64 Proper Posture During Computer Use 20 Setting a Boot Password Changing the Boot Priority Upgrading Memory Battery Installing/Removing the Battery Charging the Battery Measuring the Remaining Battery Charge Extending the Battery Usage Time 66 68 69 71 71 72 72 73 Using the Security Lock Port 75 Turn on the computer 46 Chapter 4. Appendix Product Specifications 78 Using Sleep Mode 48 Chapter 2. Using the computer Keyboard Touchpad CD Drive (ODD, Optional) Inserting and Ejecting a CD Blu-Ray (Optional) 50 53 54 55 56 Multi Card Slot ExpressCard Slot Adjusting the Volume 57 59 60 Bonn_R518_Dos_Eng. indb 3 2009-03-25 1:30:37 Bonn_R518_Dos_Eng_1. indd 4 2009-03-25 1:51:59 Chapter 1. [. . . ] Operation of this device is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. To prevent radio interference to licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Wireless devices are not user serviceable. Modification to a wireless device will void the authorization to use it. Contact manufacturer for service. Intentional Emitter per RSS 210 Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2. 4GHz/5GHz Band, may be present (embedded) in your notebook system. This section is only applicable if these devices are present. Refer to the system label to verify the presence of wireless devices. Wireless devices that may be in your system are only qualified for use in Canada if an Industry Canada ID number is on the system label. When using IEEE 802. 11a wireless LAN, this product is restricted to indoor use due to its operation in the 5. 15- to 5. 25-GHz frequency range. Industry Canada requires this product to be used indoors for the frequency range of 5. 15 GHz to 5. 25 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High power radar is allocated as the primary user of the 5. 25to 5. 35-GHz and 5. 65 to 5. 85-GHz bands. These radar stations can cause interference with and/or damage to this device. Bonn_R518_Dos_Eng. indb 33 2009-03-25 1:30:45 Telecommunications per DOC notice (for products fitted with an ICcompliant modem) The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operation, and safety requirements. The Department does not guarantee the equipment will operate to the users' satisfaction. Before installing this equipment, users should make sure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the inside wiring associated with a single-line individual service may be extended by means of a certified connector assembly. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should make sure, for their own protection, that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. To avoid electrical shock or equipment malfunction do not attempt to make electrical ground connections by yourself. [. . . ] To connect to a WPA wireless network, you have to configure the settings according to the network connection environment. For detailed setting information, ask your network administrator. Bonn_R518_Dos_Eng. indb 83 2009-03-25 1:31:11 Radio Specifications RF Band Supported Channels Device Standard Output Power Modulation Scheme 2. 4GHz Channels allowed per country. Transceiver MAX 10mW 11b mode : DSSS 11g mode : OFDM 11g mode**: MAX 54Mbps 11b mode: MAX 11Mbps Built-in Antenna Data Rate (Mbps)* Antenna Type * ** The data rate may differ from the real data transmission rate. 11g mode is only supported when the device is connected to an IEEE 802. 11g device. [. . . ]