User manual SAMSUNG NP-R519-DA04UA

[. . . ] SAMSUNG R517 User Guide Contents Chapter 1. Getting Started Cautions Regarding OS Support Before You Start Safety Precautions Important Safety Information Replacement Parts and Accessories Regulatory Compliance Statements WEEE SYMBOL INFORMATION Basic Items Overview Front View Status Indicators Right View Left View Back View Bottom View Attaching the Battery Connect the AC adapter Turn on the computer 6 7 9 23 25 27 39 40 41 41 42 43 44 45 45 46 46 47 Chapter 3. Settings and Upgrade LCD Brightness Control BIOS Setup Entering the BIOS Setup The BIOS Setup Screen 60 61 61 62 Proper Posture During Computer Use 20 Setting a Boot Password Changing the Boot Priority Upgrading Memory Battery Installing/Removing the Battery Charging the Battery Measuring the Remaining Battery Charge Extending the Battery Usage Time 64 66 67 69 69 70 70 71 Using the Security Lock Port 73 Turn on the computer 46 Chapter 4. Appendix Product Specifications 76 Using Sleep Mode 48 Chapter 2. [. . . ] This transmitter must not be collocated or operate in conjunction with any other antenna or transmitter except the installed Bluetooth transmitter. Operation of this device is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Wireless devices are not user serviceable. Modification to a wireless device will void the authorization to use it. FCC Statement for Wireless LAN use: "While installing and operating this transmitter and antenna combination the radio frequency exposure limit of 1mW/cm2 may be exceeded at distances close to the antenna installed. Therefore, the user must maintain a minimum distance of 20cm from the antenna at all times. This device can not be colocated with another transmitter and transmitting antenna. " 1 FCC Part 68 (If fitted with a modem device. ) This equipment compiles with part of the FCC rules. On the back of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company. This equipment uses the following USOC jacks : RJ11C An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or promises wiring using a compatible modular jack which is Part 68 compliant. See Installation Instructions for details. The REN is used to determine the quantity of devices which may be connected to telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of RENs should not exceed five (5. 0). To be certain of the number of devices that may be connected to a line, as determined by total RENs, contact the local telephone company to determine the maximum REN for the calling area. If the terminal equipment causes harm to the telephone network, the Telephone Company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advanced notice in order for you to make necessary modifications to maintain uninterrupted service. If trouble is experienced with this equipment (Modem) for repair or warranty information, please contact your local distributor. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. The user must use the accessories and cables supplied by the manufacturer to get optimum performance from the product. [. . . ] Thebatterylatchesmoveinwardsand fix the battery automatically. Charging the Battery 1 2 Attachthebatteryandconnectthe ACadaptertotheDC-injackofthe computer. Thebatterywillthenstart charging. Whenchargingiscomplete, theCharge LEDturnsred. Status Charging Check if the battery latch has been moved inwards. Charge LED Red Green Off Charging complete AC adapter not connected Measuring the Remaining Battery Charge You can view the battery charge status by completing the following procedures. To use the shortcut key to view You can only use this function after installing Windows XP or Windows Vista and installing the Easy Display Manager program with the system software media disk. (Only for Widows Vista) Press the Fn + ( ) keys on the keyboard. The remaining battery charge (%) will displayed for a moment. 0 To view on the battery Separate the battery and press the PUSH button inside the battery. The remaining battery charge (%) will be displayed. Extending the Battery Usage Time Decreasing the LCD Brightness Press the Fn + ( ) keys on the keyboard to decrease the LCD brightness to extend the battery usage time. Battery Warning You will hear an alarm when the remaining battery charge reaches below 10%. [. . . ]