User manual SAMSUNG NP-X11

[. . . ] Notices No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical photocopying, recording or otherwise, without the prior written permission of the manufacturer. The information within this manual is subject to change without notice. The manufacturer shall not be held liable for technical or editorial errors or omissions contained in herein; nor for incidental or consequential damages resulting from the furnishing, performance or use of this material. Microsoft Windows is a registered trademark of the Microsoft Corporation. [. . . ] When using memory in dual channel, using memory of the same specification (the same capacity and manufacturer) is recommended. 1. Using a screwdriver, open the memory module compartment cover on the bottom of the computer. screw 2. Push the memory module tabs outward to pop the memory module upwards. Carefully pull the module out at an angle of about 30. 112 Users Manual Adding a memory module 1. Align the new memory module connectors accordingly and slide it into the slot at a 30 angle. Ensure the notch on the memory module corresponds with the notch on the socket. 2. Push the memory module in until the module clicks into place. If the memory module is not fixed completely, gently push the memory down while pressing the memory module tabs outward. 3. Close and fix the memory module compartment cover using a screwdriver. System Management 113 Using the Security Lock Port The security lock is a device used to physically 'fix' the system when using it in a public place. The locking device needs to be purchased separately. The shape and methods of use may differ depending on the manufacturer. Please refer to the manual provided with the security lock for proper use. Connect a security lock cable to a fixed object. While holding the security lock port lever to the left, connect the cable to the security lock port. Any damage to the machine caused by using a locking / security device is not covered under warranty. 114 Users Manual Tips for Using Your Computer The following information helps you avoid potential problems as you use your computer: Do not try to disassemble your computer. Opening the system chassis voids your warranty. Only an authorised manufacturer service center can replace or add any parts inside the chassis. Follow all the instructions and cautions in your computer user documentation. The LCD has a polarized surface and can be damaged easily. To prevent damage, avoid touching the screen. Use only approved AC adapters, auto adapters, memory modules and other options. Because a notebook computer is small and has restricted air flow around components, it is more likely to overheat than a desktop computer. A fan inside your computer runs when needed to help eliminate heat. Make sure the fan vent on the left side of your computer is not blocked when you use the computer. Occasionally check the vents and remove any accumulated dust on the outside. Avoid using or storing the computer in extremely hot or cold areas, such as a car on a hot day. Keep the computer away from heaters and out of direct sunlight. Exposure to excessive heat may damage computer components. [. . . ] ͧʴ Press any key to boot from CD ͧ ͤسʡͻͧ Windows ¶֧Դó 蹫մ system recovery ͡Դ ;पѹҧ ҡ红 System Software 136 ͼ ҡسöѹ Windows ҡسöѹ Windows سͧͧ蹫մ system recovery Դ Windows ҡس ͧ蹫մ system recovery سöԴ Windows ͡ user installation ҹ öԴ͡ standard installation 1. ҡҡͤ仹鹷˹Ҩ 顴 鹾 Press any key to boot from CD. . . . . ͤлҡ੾աá˹աú٨ҡÿմҹ ҡҡͤ ˹Ҥ͹ԡÿմػóáѺú ´ "¹ӴѺú" ˹ 86 3. 㹢й ѧҡ鹨лҡ˹Ҩ͡˹Ҥ͹ԡ ҡͧ¹ŧ觾Ԫѹ 顴 <Enter> 4. ͡кͧ ( format ) ѡк 顴 <Enter> 5. ͡ѺԴкԺԡ Windows źѹͧ Windows ԴŧѨغѹ 顴 <L> 鹾 6. [. . . ]