User manual SAMSUNG NP-X60 PLUS

[. . . ] Notices No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical photocopying, recording or otherwise, without the prior written permission of the manufacturer. The information within this manual is subject to change without notice. The manufacturer shall not be held liable for technical or editorial errors or omissions contained in herein; nor for incidental or consequential damages resulting from the furnishing, performance or use of this material. Microsoft Windows is a registered trademark of the Microsoft Corporation. [. . . ] wireless LAN, 1394 , etc. ) Battery Calibration If you charge/discharge the battery repeatedly for only a short time, the battery use time may be reduced by the difference between the actual battery charge and the remaining charge display. In this case, the actual battery charge and the remaining charge display will be same by discharging the battery completely using the Battery Calibration function, and then recharging it again. Disconnect the AC power adapter after turning off the system. Restart your computer and press <F2> to enter BIOS setup. Using the arrow keys, highlight Smart Battery Calibration in the Boot menu. The Battery Calibration function is activated and the battery is discharged forcibly. This operation requires 3~5 hours depending on the battery capacity and the remaining battery charge. When the calibration process is complete, recharge the battery fully. System Management 111 Upgrading Memory This computer has one or more 256 MB or 512 MB memory module(s). Two memory module sockets are provided so that you can replace memory or install an additional memory module. Removing the memory module Before removing/replacing the memory module, turn the system off completely and remove the battery. Do not replace the memory module when the system is in Standby/Hibernate mode. When using memory in dual channel, using memory of the same specification (the same capacity and manufacturer) is recommended. 1. Using a screwdriver, open the memory module compartment cover on the bottom of the computer. screw 2. Push the memory module tabs outward to pop the memory module upwards. Carefully pull the module out at an angle of about 30. 112 Users Manual Adding a memory module 1. Align the new memory module connectors accordingly and slide it into the slot at a 30 angle. Ensure the notch on the memory module corresponds with the notch on the socket. 2. Push the memory module in until the module clicks into place. If the memory module is not fixed completely, gently push the memory down while pressing the memory module tabs outward. 3. Close and fix the memory module compartment cover using a screwdriver. System Management 113 Using the Security Lock Port The security lock is a device used to physically 'fix' the system when using it in a public place. The locking device needs to be purchased separately. The shape and methods of use may differ depending on the manufacturer. Please refer to the manual provided with the security lock for proper use. Connect a security lock cable to a fixed object. [. . . ] ͧʴ Press any key to boot from CD ͧ ͤسʡͻͧ Windows ¶֧Դó 蹫մ system recovery ͡Դ ;पѹҧ ҡ红 System Software 138 ͼ ҡسöѹ Windows ҡسöѹ Windows سͧͧ蹫մ system recovery Դ Windows ҡس ͧ蹫մ system recovery سöԴ Windows ͡ user installation ҹ öԴ͡ standard installation 1. ҡҡͤ仹鹷˹Ҩ 顴 鹾 Press any key to boot from CD. . . . . ͤлҡ੾աá˹աú٨ҡÿմҹ ҡҡͤ ˹Ҥ͹ԡÿմػóáѺú ´ "¹ӴѺú" ˹ 89 3. 㹢й ѧҡ鹨лҡ˹Ҩ͡˹Ҥ͹ԡ ҡͧ¹ŧ觾Ԫѹ 顴 <Enter> 4. ͡кͧ ( format ) ѡк 顴 <Enter> 5. ͡ѺԴкԺԡ Windows źѹͧ Windows ԴŧѨغѹ 顴 <L> 鹾 6. [. . . ]