User manual SAMSUNG NS071LDXEA

[. . . ] USER'S MANUAL Wired Remote Controller MWR-WH01 System Air Conditioner E S F I P D G Ne Po Hu R A DB98-31483A(1) MWR-WH00_IB_E_31218-1. indd 21 2009-12-14 5:24:58 RUSSIAN MAGYAR POLSKI NEDERLANDS EHNIKA DEUTSCH PORTUGUÊS ITALIANO FRANÇAIS ESPAÑOL ENGLISH Safety Precautions · Before using the wired remote controller, read carefully these instructions. · After reading the instructions, keep this user's manual in a handy and safe place. If a user is changed, you must hand over the manuals. · Never attempt to install the air conditioning system or to move the wired remote controller by yourself. WARNING o not attempt to install or repair this wired remote D controller by yourself. his remote controller contains no user-serviceable parts. [. . . ] Result: T he temperature will be adjusted by 1°C(1°F) when the buttons are pressed. 4 To adjust the air swing direction, refer to page 13. E-8 MWR-WH00_IB_E_31218-1. indd 8 2009-12-14 9:47:00 Selecting the Fan Mode Select the fan mode to circulate air without changing the temperature. 1 Press the (ON/OFF) button to turn on the indoor unit. - Do not press the (ON/OFF) button if the remote controller is on. Result: T he air conditioner will be turned on with the most recently used mode. The air conditioner has a built-in protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped The air conditioner will start up after 3 minutes. 2 To select the FAN mode, press the displayed on the remote controller. Result: button until Fan is The air conditioner will operate in fan mode. You cannot adjust the temperature in fan mode. 3 Select the fan speed by pressing the Result: button. E ach time the button is pressed, fan speed will change in the following order: Low Med High 4 To adjust the air swing direction, refer to page 13. E-9 MWR-WH00_IB_E_31218-1. indd 9 2009-12-14 9:47:02 ENGLISH Selecting the Heating Mode The heating mode can be selected only on the heat pump models. Select the heat mode to raise the room temperature. 1 Press the (ON/OFF) button to turn on the indoor unit. - Do not press the (ON/OFF) button if the remote controller is on. T he air conditioner will be turned on with the Result: most recently used mode. The air conditioner has a built-in protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped The air conditioner will start up after 3 minutes. To select the HEAT mode, press the button until Heat is displayed on the remote controller. Result: The air conditioner will operate in heating mode. To adjust the temperature, press the buttons. The temperature can be set between 16°C(61°F) and 30°C(86°F). Result: The temperature will be adjusted by 1°C(1°F) when the buttons are pressed. The air conditioner will start heating if the set temperature is higher than the room temperature. The fan will operate even if the set temperature is lower than the room temperature. 2 3 4 Select the fan speed by pressing the Result: button. E ach time the button is pressed, fan speed will change in the following order: Low Med High Auto 5 To adjust the air swing direction, refer to page 13. After starting heating operation, the air may not come out immediately to prevent the cold air from coming out. (Defrost indicator) - Defrost indicator will be on while your outdoor unit defrosts the frost formed during heating operation. After defrosting is completed, the indicator will be off. (Air will not come out of the indoor unit while defrosting. ) If you stop running the air conditioner after heating operation, the air will come out for a while to radiate heat. If you select cooling mode while the heating mode is in operation, heating mode will be canceled. Note E-10 MWR-WH00_IB_E_31218-1. indd 10 2009-12-14 9:47:03 Selecting the Quiet Mode Select the quiet mode to run the indoor unit as quietly as possible. 1 Press the (ON/OFF) button to turn on the indoor unit. - Do not press the (ON/OFF) button if the remote controller is on. [. . . ] If you select 0, auto stop function will be canceled. button to complete the auto stop function. To cancel the auto stop function, press the button. will be displayed. 3 Press the Result: Note 4 Press the Result: Note The time-counting of Auto Stop function is clear after pressing the , , , , , buttons. [. . . ]