User manual SAMSUNG P2250W

[. . . ] SyncMaster P2250W LCD Monitor User Manual The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Table Of Contents MAJOR SAFETY PRECAUTIONS Before You Start . 1-3 INSTALLING THE PRODUCT Package Contents . 2-3 Installing the Stand for the Wall Mount . 2-6 USING THE PRODUCT Setting the Optimal Resolution . [. . . ] Insert the driver installation CD-ROM into the CD-ROM drive. Select the model of your product from the model list. 4. Complete the remaining installation steps according to the instructions displayed on the screen. Check if the appropriate resolution and screen refresh rate are displayed in the Control Panel settings. For more information, refer to the document about the Windows operating system. 3-3 Using the product 3-4 Product Operating Buttons Product Operating Buttons Touch one of the operating buttons lightly. ICON MENU DESCRIPTION Press this button to view the On Screen Display (OSD). This button is also used to exit the OSD or to return to a higher-level OSD menu * OSD Adjustment Lock This function locks the OSD in order to maintain the current settings or to prevent the settings from being changed by another person On: If you press and hold the MENU button down for 5 seconds, the OSD Adjustment Lock function is activated. Off: If you press and hold the MENU button down for 5 seconds again, the OSD Adjustment Lock function is disabled. Even if the OSD Adjustment Lock function is activated, users can adjust the brightness and contrast and can set up the adjustment function assigned to the [ ]. / Use these buttons to navigate the menu or to adjust a value in the OSD. Users can set the Customized Key to one of the following functions. If the user presses the Customized Key[ ] after setting it, the configured function will be performed <MagicBright> - <MagicColor> - <Color Effect> - <Image Size> You can set the function of the Customized Key by selecting "SETUP&RESET -> Customized Key" in the OSD. Use this button to control the brightness of the screen. If you press the [ ] button when there is no OSD, the input signal (analog/digital) is switched. When the input signal is switched by pressing [ ] button or the product is turned on, a message displaying the selected input signal appears at the top left of the screen. ) To select digital mode, you have to connect the product and the PC with the DVI cable. Using the product 3-4 ICON AUTO DESCRIPTION Press [AUTO] button to adjust the screen settings automatically This function is only available in analog mode. If the resolution settings are changed in the Display Properties, the AUTO adjustment function is performed. Press this button to turn the product on or off · · The buttons on the right of the product are touch-type buttons. Touch the buttons lightly with your finger. Power LED This LED is turned on when the product works normally. For more information on the power-saving function, refer to the power saving function in More Information. When not using the product for a long time, unplugging the power cord is recommended to minimize power consumption. 3-4 Using the product 3-5 Using the Screen Adjustment Menu (OSD: On Screen Display) The Screen Adjustment Menu (OSD: On Screen Display) Structure TOP MENUS PICTURE Brightness Fine COLOR MagicColor Color Effect SIZE & POSITION H-Position Contrast Response Time Red Gamma V-Position Image Size Menu H-Position Menu V-Position Green Blue Color Tone SUB MENUS Sharpness MagicBright Coarse Reset SETUP&RESET Off Timer On/Off Customized Key INFORMATION Menu Transparency Off Timer Setting Language Auto Source LED On/Off PC/AV Mode LED Brightness Display Time PICTURE MENU Brightness Controls the screen brightness. DESCRIPTION This menu is unavailable when <MagicBright> is set to <Dynamic Contrast> mode. Contrast Controls the contrast of the pictures displayed on the screen This menu is unavailable when <MagicBright> is set to <Dynamic Contrast> mode. This menu is unavailable when <MagicColor> is set to <Full> mode or <Intelligent> mode. [. . . ] Install the device driver referring to the descriptions about the driver installation. WHEN I LOOK AT THE EXTERIOR EDGES OF THE PRODUCT, SMALL ALIEN SUBSTANCES APPEAR ON IT. Since this product is designed so that the color has a soft appearance by coating it with a transparent material over the black edges, such things may be seen. A "BEEP, BEEP" SOUND IS HEARD WHEN BOOTING THE COMPUTER. If the beep sound is generated 3 or more times when booting up the computer, please request service for the computer. 5-2 Troubleshooting 5-3 FAQ FAQ! [. . . ]