User manual SAMSUNG PL-50P5HD

[. . . ] Owner's Instructions PL-42P5HD PL-50P5HD This device is a Class B digital apparatus. Register your product at www. samsung. com/global/register Important Warranty Information Regarding Television Format Viewing Wide screen format PDP Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature and the images are constantly moving. Displaying stationary graphics and images on screen, such as the dark side-bars on nonexpanded standard format television video and programming, should be limited to no more than 5% of the total television viewing per week. [. . . ] Click on the Monitor tab, then set the Screen Refresh Rate with reference to the Display Modes Table. Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of setting the Screen Refresh Rate. Press the OK button, close the window, then press the OK button on the Display Registration Information window. Automatic re-booting may commence at this moment. Shutdown the PC, and connect it to your TV. (See page 86) · The actual screens on your PC may look different, depending on your particular version of Windows and the type of your PC. · When you use your TV as a PC monitor, it supports Colors up to 32 bits. · In this case, the display on the TV may look different depending on your particular version of Windows or the PC manufacturer. · When connecting a PC you must set it to the display settings that are supported by the TV. Otherwise, the message Out of input range will be displayed. 2 3 4 5 88 Continued. . . Note Both screen position and size will vary, depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported: Video Signal Resolution (Dot X Line) 640 X 350 720 X 400 640 X 480 Vertical Horizontal Frequency (Hz) Frequency (KHz) 70. 086 70. 087 59. 940 70. 000 72. 809 75. 000 800 X 600 IBM PC / AT Compatible 56. 250 60. 317 70. 000 72. 188 75. 000 1024 X 768 60. 004 70. 069 72. 000 75. 029 1280 X 720 1360 X 768 · · · · 59. 855 60. 015 31. 469 31. 469 31. 469 35. 000 37. 861 37. 500 35. 156 37. 879 43. 750 48. 077 46. 875 48. 363 56. 476 57. 672 60. 023 44. 772 47. 712 Vertical Polarity P N N N/P N N N/P P N/P P P N N N/P P P P Horizontal PL-42P5HD PL-50P5HD Polarity N P N N/P N N N/P P N/P P P N N N/P P N P The interlace mode is not supported. The TV operates abnormally if a non-standard video format is selected. The table above conforms to IBM/VESA regulations and is based on using the Analog Input. A "" mark means that this mode can be supported. Notes · · · · The PC text quality of PL-42P5HD is optimum in XGA mode (1024 x 768@60Hz). The PC text quality of PL-50P5HD is optimum in WXGA mode (1360 x 768@60Hz). When this TV is used as a PC display, 32-bit color is supported. Depending on the manufacturer, your PC display screen might appear different. (and depending on your particular version of Windows. ) Check your PC instruction book for information about connecting your PC to a TV. · If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 48. 4KHz (horizontal). · In some cases, abnormal signals (such as stripes) might appear on the TV screen when the PC power is turned off (or if the PC is disconnected). If so, press the SOURCE button on the remote control or SOURCE button on the front panel to enter the VIDEO mode. Also, make sure that the PC is connected. [. . . ] Check to see that both the TV and the source are plugged in and turned on. Adjust the Brightness or Contrast settings. Please check the digital signal strength and input antenna. On your computer check; Power, Signal Cable. [. . . ]