User manual SAMSUNG PN50A550S1F

[. . . ] % SOURCE Press to display all of the available video sources. CH Press to change channels. 5 3 NUMERIC BUTTONS Press to directly select a channel. W. LINK & 4 ­ W. LINK Press to select additional channels (digital and analog) being broadcast by the same station. For example, to select channel "54-3", press "54", then press "­" and "3". [. . . ] If your VCR is stereo, you must connect two cables. Each VCR has a different back panel configuration. When connecting to AV IN 1, the color of the AV IN 1 [Y/VIDEO] jack (Green) does not match the color of the video cable (Yellow). If you have a "mono" (non-stereo) VCR, use a Y-connector (not supplied) to hook up to the right and left audio input jacks of the Connecting to S-Video TV Rear Panel VCR Rear Panel TV Side Panel 1 2 3 2 Antenna Cable (Not supplied) Audio Cable (Not supplied) S-Video Cable (Not supplied) 4 To begin, follow steps 1­3 in the previous section to connect the antenna or cable to your VCR and your TV. Connect a S-Video cable between the [S-VIDEO] jack on the TV and the S-VIDEO OUT jack on the VCR. Connect Audio cables between the AV IN 2 [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the VCR. Press the SOURCE button on the remote control until you see the VCR signal (see "To Select the Source" on page 10). When connecting a VCR, match the color of the connection terminal to the cable. Each VCR has a different back panel configuration English - 5 Connecting a Digital Audio System TV Rear Panel Digital Audio System 1 Connect an Optical Cable between the DIGITAL AUDIO OUT (OPTICAL) jacks on the TV and the Digital Audio Input (OPTICAL) jacks on the Digital Audio System. When a Digital Audio System is connected to the DIGITAL AUDIO OUT (OPTICAL) terminal: Decrease the volume of the TV, and adjust the volume level with the system's volume control. What is OPTICAL? Optical Cable (Not supplied) · Converts the electric signal into an optical light signal, and transmits it through glass fibers. S/PDIF is a transmission system of digital audio in the form of a light wave that uses a glass conductor. is connected to an external device supporting 5. 1CH. 5. 1CH audio is possible when the TV Each external input source device has a different back panel configuration. When the COMPONENT IN or HDMI IN jacks are connected, the Optical jack on the TV outputs 2 channel audio only. If you want to hear 5. 1 channel audio, connect the DIGITAL AUDIO OUT (OPTICAL) jack on the DVD player or Cable/Satellite Box directly to an Amplifier or Home Theater, not the TV. Connecting an Analog Amplifier / DVD Home Theater TV Rear Panel 1 Connect Audio Cables between the AUDIO OUT [R-AUDIO-L] on the TV and AUDIO IN [L-AUDIO-R] on the Amplifier / DVD Home Theater. Analog STD Start HRC IRC STD HRC IRC 1 Press the MENU button. Press the or button to select Channel, then press the ENTER button. TV Channel Antenna : Air Auto Program Clear Scrambled Channel Channel List Name Fine Tune Signal Strength Move Enter Return Digital Move Enter Return English - 8 4 When selecting the Cable TV system: Press the ENTER button to start the auto program. Press the or to select the correct analog signal cable system source from among STD, HRC, and IRC, then press the ENTER button. Press the EXIT button to exit. Cell Light Move Adjust Return 10 1 2 Press the MENU button to display the menu. Press the ENTER button to select Picture. Press the or button to select Dynamic, Standard, or Movie. Dynamic: Select the picture for high-definition in a bright room. Standard: Select the picture for the optimum display in a normal environment. Movie: Select the picture for viewing movies in a dark room. TV Mode Cell Light Contrast Brightness Sharpness Color Tint G 50 More Move Picture : Dynamic Standard Movie Contrast Move Adjust Return 100 When you make changes to Cell Light, Contrast, Brightness, Sharpness, Color, or Tint(G/R) the OSD will be adjusted accordingly. When in PC mode, Tint(G/R), Sharpness and Color are not available. Each adjusted setting will be stored separately according to its input mode. 10 100 45 75 55 R 50 Return To Select the Source Use to select TV or other external input sources such as DVD players or Set-top/Cable boxes connected to the TV. [. . . ] Remote control malfunctions First, check the volume of units connected to your TV (digital broadcasting receiver, DVD, cable broadcasting receiver, VCR, etc. ). Unplug the TV for 30 seconds, then try operating it again. Clean the upper edge of the remote control(transmission window). Check that the "+" and "-" ends of the batteries are inserted correctly. Digital broadcasting screen problem. [. . . ]