User manual SAMSUNG PPM42M7HB

[. . . ] Height The PDP Monitor can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not install and operate there. Heat on the top of the PDP Monitor The top side of the product may be hot after long periods of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. [. . . ] Result: The following options are available. 16:9 : Sets the picture to 16:9 wide mode. Panorama : Use this mode for the wide aspect ratio of a panoramic picture. Zoom1 : The screen size when wide screen is vertically enlarged. Zoom2 : The screen size when the Zoom1 screen is vertically enlarged. 14:9 : Magnify the size of the picture more than 4:3. 4:3 : Sets the picture to 4:3 normal mode. Size 16:9 Panorama Zoom1 Zoom2 14:9 4:3 Adjust Enter Return PC to DVI Mode TV 16:9 Panorama Zoom1 Zoom2 14:9 4:3 Size 6 Press the ENTER ( ) button. You can select these options simply by pressing the P. SIZE button on the remote control. If you change the picture size In PIP mode, PIP disappears automatically. Depending on the input source, the P. SIZE options may vary. Check if the Video Wall (refer to page 33) is On if the Picture size is not function. Picture size does not function when the Video Wall is set to On. To cancel the Remote Control Button Lock, press "0000" using the numeric buttons on the remote control. Move Enter Return IR Lock : On English - 27 Setting Up Your Personal ID Number This feature sets viewing restrictions and prevents unauthorized access to your PDP Monitor through the PIN (Personal Identification Number), which is a 4 digit number. TV Function Screen Burn Protection Safety Lock Multi Control Video Wall Fan : Off 1 Press the MENU ( Result: ) button. The main menu is displayed. 2 Move Enter Return Press the or button to select Function. ) button. TV Key Lock IR Lock Change PIN Safety Lock : Off 3 4 5 6 Press the ENTER ( Press the or button to select Safety Lock. Press the or button to select Change PIN. Press the number buttons to enter your current 4-digit pin number. Move Enter Return 7 The default pin number for a new PDP Monitor set is "0000". TV Change PIN Press the numeric buttons to enter your new 4-digit pin number. Re-enter your new pin number to confirm. Enter PIN Enter New PIN Return If you forget the pin number, press the remote control buttons in the following sequence, which resets the pin to 0-0-0-0: MUTE, 1, 8, 6. Adjust TV Change PIN Enter PIN * * * Enter New PIN * Adjust Return English - 28 Setting the MDC (Multiple Display Control) This function enables you to easily control the connected monitors on the PC by specifying IDs to connected monitors. TV Function Screen Burn Protection : Off 1 Press the MENU ( Result: ) button. Safety Lock Multi Control Video Wall Fan The main menu is displayed. 2 Press the or button to select Function. Result: The Function menu is displayed. Move Enter Return 3 4 5 Press the ENTER ( ) button. TV ID Setup Multi Control : : 00 - Press the or button to select Multi Control. Press the ENTER ( Result: ) button. ID Input The Multi Control menu is displayed with the ID Setup selected. 6 Press the ENTER ( ) button again. Select the ID setup number by pressing the , , or numeric buttons. Press the or button to select ID Input. Enter ID input number by using the numeric buttons. Press the ENTER ( ) button. TV Move Enter Return 7 8 Multi Control ID Setup ID Input : : 00 -- 00 To operate the multi control function, PDP1 and PDP2 should be set in the ID Setup mode. [. . . ] In this case, the display on the PDP Monitor may look different depending on your particular version of Windows or the PC manufacturer. When connecting a PC (including the DVI connection), you must set it to the display settings that are supported by the PDP Monitor. Otherwise, the message Out of input range will be displayed. English - 47 Input Mode (PC/DVI) Both screen position and size will vary depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported: Resolution VGA 640 x 350 640 x 400 720 x 400 640 x 480 Vertical Horizontal PPM42M5S PPM42M5H PPM50M5H PPM63M5H frequency (Hz) frequency (kHz) 70 85 85 70 85 60 72 75 85 56 60 72 75 85 60 70 75 85 60 72 75 85 60 75 60 75 60 75 60 60 60 31. 5 37. 9 37. 9 31. 5 37. 9 31. 5 37. 9 37. 5 43. 3 35. 2 37. 9 48. 1 46. 9 53. 7 48. 4 56. 5 60. 0 68. 7 29. 8 35. 1 36. 0 37. 0 31. 8 67. 5 64. 0 80. 0 47. 7 60. 1 47. 8 48. 2 75. 0 / / / / / / / / / / / / / / / / / / / / / / / / / / SVGA 800 x 600 XGA 1024 x 768 WVGA 848 x 480 SXGA WXGA 852 x 480 1152 x 864 1280 x 1024 1280 x 768 1360 x 768 1366 x 768 1600 x 1200 UXGA "" mode does not work with DVI mode. [. . . ]