User manual SAMSUNG PS-42P2STR

[. . . ] ELECT PLASMA DISPLAY PS42P2S Owner's Instructions Before operating the unit, please read this manual thoroughly, and retain it for future reference. REMOTE CONTROL ON-SCREEN MENUS PICTURE IN PICTURE TELETEXT ENG Safety Instructions ENG N Do not place the PDP on an unstable cart, stand, tripod, bracket, table, or floor where it can fall. N Do not expose the PDP to extreme temperature conditions or to extreme humidity conditions. N Do not expose the PDP to direct sunlight and other sources of heat. N Never put objects of any kind into the television, and do not place a water-containing vessel on the PDP. [. . . ] To display the subpage, see the following steps. Sub-pages can be scrolled by using the or button. 3 4 5 Press the Text/Off button to exit from the teletext display. 32 Connecting a PC ENG N Connect a PC cable (15pin) between the PC and PDP. N Connect an Audio cable between the Audio output jack on the PC and the Audio input jack (PC) on the PDP. Rear panel Viewing the PC screen: 1 Turn on PDP and select the PC mode by pressing the Source (or Source/PC) button on the remote control. Turn on PC and check for PC system requirements. (Refer to pages 35~37 for PC system requirements. ) Adjust the PC screen. (Refer to page 38. ) 2 3 PC Pin Configuration 1 6 11 7 12 2 8 13 14 3 4 10 15 5 15Pin Signal Cable (based on protruded pin) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PC IN Red (R) Green (G) Blue (B) Grounding Grounding (DDC) Red (R) Grounding Green (G) Grounding Blue (B) Grounding Reserved Sync Grounding Grounding Data (DDC) Horizontal sync. Clock (DDC) PC OUT Red (R) Green (G) Blue (B) Grounding Grounding (DDC) Red (R) Grounding Green (G) Grounding Blue (B) Grounding Reserved Sync Grounding Grounding Data (DDC) Horizontal sync. Clock (DDC) 33 Setting up Your Display Plug and Play ENG Our adoption of the new VESA Plug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system without the usual hassles and confusion. Your PC system can easily identify and configure itself for use with your display. This monitor automatically tells the PC system its Extended Display Identification data (EDID) using Display Data Channel (DDC) protocols. Preset Signals Source Video NTSC3. 58 PAL Vertical frequency (Hz) 60 50 50 60 60 50 60 50 60 50 60 50 60 Horizontal frequency (kHz) 15. 704 15. 625 15. 625 15. 734 15. 734 15. 625 15. 734 15. 625 31. 469 31. 250 45. 000 28. 125 33. 750 Resolution (Lines) 483 575 575 483 483 575 483 575 483 575 720 1080 1080 AV1(Video) AV1(S-Video) SECAM NTSC4. 43 PAL-M PAL-N 480/60i 576/50i 480/60p 576/50p 720/60p 1080/50i 1080/60i Component 1 Component 2 When the 576/50p signal is received, the picture might be displayed abnormally or shift, depending on the receiver or A/V component. In that case, you can try "Chaning the Screen Position" on page 39. (But the screen position might be unmatched depending on the component. ) 34 Setting up Your PC Software (Windows only) ENG The Windows display-settings for a typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. On the windows screen, select in the following sequence: Start Settings Control Panel. When the control panel screen appears, click on "Display" and a display dialog-box will appear. Select the "Settings" tab in the display dialog-box. The two key variables that apply the PDP-PC interface are "Resolution" and "Colors". The correct settings for these two variables are: N Size (sometimes called "Resolution") 1024 x 768 pixels. N Color "24-bit" color (might also be expressed as "16 million colors") Shown at left is a typical screen for "Display" dialog box. If a vertical-frequency option exists on your display settings dialog box, the correct value is "60" or "60Hz". Otherwise, just click "OK" and exit the dialog box. 35 PC Input Mode (42") ENG Both screen position and size will vary depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported: Standard VGA Dot x Line 640 x 480 Vertical frequency (Hz) 85. 0 75. 0 72. 8 59. 9 720 x 400 SVGA 800 x 600 70. 1 85. 1 75. 0 72. 2 60. 3 56. 3 XGA 1024 x 768 85. 0 75. 0 70. 1 60. 0 Horizontal frequency (kHz) 43. 3 37. 5 37. 9 31. 5 31. 5 53. 7 46. 9 48. 1 37. 9 35. 2 68. 7 60. 0 56. 5 48. 3 Vertical polarity N N N N P P P P P P P P N N Horizontal polarity N N N N N P P P P P P P N N (N: Negative / P: Positive) N The interlace mode is not supported. N The PDP might operate abnormally if a non-standard video format is selected. [. . . ] Both On Timer and Off Timer functions have been set, but a different time is applied. - Apply the current time to set the time of each display equal. ^ The remote control may not function properly if you disconnect the RS-232C cable or exit from the programs in an irregular manner even with the remote control function is OFF. - Rerun program and turn the remote control function ON to restore normal functions. [. . . ]