User manual SAMSUNG PS-42P3ST

[. . . ] BN68-00528A-01_ENG 2003. 11. 20 4:13 PM Page 1 PDP-MONITOR (PLASMA DISPLAY PANEL) PS42P3ST Owner's Instructions Before operating the unit, please read this manual thoroughly, and retain it for future reference. Intended for Commercial Use and Operation ON-SCREEN MENUS PICTURE IN PICTURE (PIP) MDC (MULTIPLE DISPLAY CONTROL) BN68-00528A-01_ENG 2003. 11. 20 4:13 PM Page 2 Warning!Important Safety Instructions ENG CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash and arrow head within the triangle is a warning sign alerting you of "dangerous voltage" inside the product. The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product. CAUTION: TO PREVENT ELECTRICAL SHOCK, DO NOT REMOVE REAR COVER, NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Note to CATV system installer: This reminder is provided to call CATV system installer's attention to Article 82040 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. [. . . ] Press the or button to select Equalizer. Result: The Equalizer menu is displayed with the current option. 4 L 100 300 oe Move Adjust 1K 3K 10K Store 5 Select the option (volume, balance, equalizer) to be adjusted by pressing the oe or button. Press the or button to reach the required setting. When you are satisfied with the settings, press the store them. button to 6 If you make any changes to the equalizer settings, the sound mode is automatically switched to the Custom. 22 BN68-00528A-01_ENG 2003. 11. 20 4:14 PM Page 23 Extra Sound Settings ENG Auto Volume Each broadcasting station has its own signal conditions, and so it is not easy for you to adjust the volume every time the channel is changed. This feature lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low. Melody You can hear clear melody sound when the PDP is powered on or off. Mode Sound oe Custom oe Off oe Off oe Off oe Off Sel. Return Sound Mode Equalizer Auto Volume Melody Pseudo Stereo Virtual Surround Move Sel. oe Custom oe Off oe Off oe Off oe Off Return Pseudo Stereo / Virtual Surround Pseudo stereo feature converts a monaural sound signal into two identical left and right channels. Once the Pseudo stereo or Virtual surround is set to On or Off, these settings apply to the sound effects such as Standard, Music, Movie, and Speech. Equalizer Auto Volume Melody Pseudo Stereo Virtual Surround Move Sound 1 Press the MENU button. Result: The main menu is displayed. Mode Equalizer Auto Volume Melody Pseudo Stereo Virtual Surround Move Sel. oe Custom oe Off oe Off oe Off oe Off Return 2 Press the or button to select Sound. Result: The options available in the Sound group are displayed. 3 4 Select the required option (Auto Volume, Melody, Pseudo Stereo, Virtual Surround) by pressing the or button. Press the oe or button to change the setting (Off or On). Mode Equalizer Auto Volume Melody Pseudo Stereo Virtual Surround Move Sel. Sound oe Custom oe Off oe Off oe Off oe Off Return 23 BN68-00528A-01_ENG 2003. 11. 20 4:14 PM Page 24 Adjusting the Image Preferences (PC Mode) ENG Setup Image Lock Key Lock Multi Control Burning Protection Information oe Off 1 2 3 Press the MENU button. Result: Press the or button to select Setup. The options available in the Setup group are displayed. The Image Lock menu is displayed with the Auto Result: Adjustment selected. The screen size and frequency are automatically reset Result: with the Auto Adjustment displayed. Move Enter Return 4 Image Lock Auto Adjustment Frequency Phase Position Zoom/Panning Move Enter Return 5 6 You can also do simply by pressing the AUTO button. Frequency 0 oe Adjust Press the or button to select Frequency (or Phase). Move the horizontal Result: bar's cursor left or right by pressing the oe or button. When you are satisfied with the settings, press the MENU button. Result: Press the or button to select Position. Adjust the screen position by pressing the , , oe, or button. [. . . ] This power management system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. This power management system operates with a VESA DPMS compliant video card installed in your computer. You use a software utility installed on your computer to set up this feature. Normal Operation Active Active Active Off Power-saving Function Mode Standby Mode Inactive Active Blanked Red Blinking (1 sec Interval) Suspend Mode Position A1 Active Inactive Blanked Red Blinking (1 sec Interval) Power-off Mode Position A2 Inactive Inactive Blanked Red Blinking (1 sec Interval) State Horizontal Sync Vertical Sync Video Power Indicator This monitor automatically returns to normal operation when horizontal and vertical sync return. [. . . ]