User manual SAMSUNG PS-50P7HR

[. . . ] PDP-TELEVISION (PLASMA DISPLAY PANEL) Owner's Instructions Before operating the unit, please read this manual thoroughly, and retain it for future reference. ON-SCREEN MENUS Picture In Picture (PIP) Energy Saving TELETEXT (Option) SRS TruSurroundXT Digital Natural Image engine Register your product at www. samsung. com/global/register User Instructions Screen Image retention Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as "screen burn". To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image. Height The PDP can normally operate only under 2000m in height. [. . . ] Press any button on the remote control to cancel this feature. English - 24 Setting the Blue Eye You can set the power of Blue LED to be on. If the power is off when Blue Eye is off, the Blue LED goes off after 5 seconds. This will save power and reduce eye fatigue. 1 2 3 4 Press the MENU ( ) button to display the menu. ) Move Enter Return TV More Energy Saving Blue Eye Setup : Off : On Screen Burn Protection Press the . . . or button to select Setup, then press the ENTER ( button. or button to select Blue Eye, then press the ENTER ( ) button. ) button. Select Off or On by pressing the . . . or button, then press the ENTER ( Off: LED(Blue) will not come on. On: LED(Blue) will come on after you turn the TV off. 5 Press the EXIT button to exit. Setting up Your PC Software (Based on Windows XP) The Windows display-settings for a typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer. ) 1 2 3 4 Right click the mouse on the Windows Desktop, then click on Properties. The Display Properties will be displayed. Click on Settings tab, then set the Display Mode with reference to the Display Modes Table. You do not need to change the Colours settings. A new settings dialog box will be displayed. Click on the Monitor tab, then set the Screen refresh rate with reference to the Display Modes Table. Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of setting the Screen refresh rate. Click on OK to close the window, then Click on OK button to the Display Properties window. Automatic re-booting may commence at this moment. 5 English - 25 Input Mode (PC) Both screen position and size will vary depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported: Resolution (Dot X Line) 640 x 350 720 x 400 Vertical frequency (Hz) 70. 086 70. 087 59. 940 70. 000 72. 809 75. 000 56. 250 60. 317 70. 000 72. 188 75. 000 60. 000 74. 769 60. 004 70. 069 72. 000 75. 029 59. 855 60. 015 Horizontal frequency (kHz) 31. 469 31. 469 31. 469 35. 000 37. 861 37. 500 35. 156 37. 879 43. 750 48. 077 46. 875 31. 020 37. 684 48. 363 56. 476 57. 672 60. 023 44. 772 47. 712 Vertical polarity N P N N/P N N N/P P N/P P P P P N N N/P P N P Horizontal polarity P N N N/P N N N/P P N/P P P P N N N N/P P P P Video Signal PS-42P7H PS-50P7H 640 x 480 IBM PC / AT Compatible 800 x 600 848 x 480 1024 x 768 1280 x 720 1360 x 768 (N: Negative / P: Positive) The interlace mode is not supported. [. . . ] No sound or picture Check that the mains lead has been connected to a wall socket. Check that you have pressed the (Power) button (On/Off) on the front panel or press the POWER ( ) button on the remote control. Check the picture contrast and brightness settings. Normal picture but no sound Check the volume. [. . . ]