User manual SAMSUNG PS50B451B2WXXC

[. . . ] To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image. Height The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not install and operate there. Heat on the top of the PDP TV The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper part of the product. [. . . ] The after image removal function has to be executed for a long time (approximately 1 hour) to effectively remove after images on the screen. If after image is not improved after the execution of the function, repeat the function again. Press any button on the remote control to cancel this feature. D Effect: Mode/Format You can enjoy 3D movies and games on your TV. The 3D effects function enables you to view 3D images using special 3D glasses. Connections D Glasses (Not supplied) D IR Emitter (Not supplied) TV Rear Panel PC . 5 mm Stereo plug to RCA Cable (Not supplied) HDMI/DVI Cable (Not supplied) The appearance of the 3D glasses (including Emitter) may differ depending on the model of your glasses. 1 4 Connect a HDMI/DVI cable between the HDMI IN 2 jack on the TV and the PC output jack on your computer. Connect a 3. 5mm Stereo/2RCA cable between the DVI IN (HDMI 2) [R-AUDIO-L] jack on the TV and the Audio Out jack of the sound card on your computer. Connect the Emitter to the 3D SYNC OUT port on the rear panel of the TV. Turn the TV on and set the source of the TV to HDMI2. Continued. . . English - For more information on the 3D glasses (including the Emitter), refer to the user manual of your 3D glasses. Adjust the PC resolution - PS42A450 : 1024 x 768@60Hz - PS50A450 : 1024 x 768@60Hz 1360 x 768@60Hz The 3D IR Emitter communicates with the 3D glasses. Therefore, the 3D IR Emitter should be located near the 3D glasses. It is activated when the HDMI or DVI input signal is RGB, and DVI Sound is supported. 5 Press the or button to select Format, then press the ENTER button. Press the or button to select Checker Board, Horizontal or Vertical then press the ENTER button. Checker Board Horizontal Vertical If the output format of your graphic card or 3D software is Checkerboard, select this input format. If the output format of your graphic card or 3D software is Horizontal interleaved, select this input format. If the output format of your graphic card or 3D software is Vertical interleaved, select this input format. Move Enter Return TV Mode Format D Effect : Mode 1 : Checker Board Checker Board Horizontal Vertical Move Enter Return English - Resetting the Picture Settings to the Factory Defaults You can set detailed picture settings. 1 4 Press the MENU button to display the menu. Press the ENTER button to select Picture. Press the or button to select Reset, then press the ENTER button. Press the or button to select OK or Cancel then press the ENTER button. TV Picture Mode : Standard Cell Light Contrast 5 Brightness 45 Sharpness 50 Colour 50 Tint G 50 R 50 Detailed Settings Picture Options Reset : OK OK Cancel Move Enter Return Each mode can be reset. Sound Features 1 Press the MENU button to display the menu. Press the or button to select Sound, then press the ENTER button. Select the required option by pressing the or button, then press the ENTER button. Available options: Mode, Equalizer, SRS TS XT, Auto Volume, TV Speaker, Sound Select When you are satisfied with your setting, press the ENTER button. [. . . ] Check the picture contrast and brightness settings. Normal picture but no sound Check the volume. Check whether the volume MUTE button on the remote control has been pressed. No picture or black and white picture Adjust the colour settings. [. . . ]