User manual SAMSUNG RS20NCSM

[. . . ] ENGLISH SIDE BY SIDE REFRIGERATOR Write the model and serial number here: Model # Serial # Find these numbers on a label of the refrigerator cabinet at the left hand-side wall. RS OWNER'S MANUAL AND INSTALLATION Before operating the appliance, please read this manual carefully and retain for future reference. CONTENTS SAFETY WARNING SIGNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PREPARING THE APPLIANC FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Do not use a wet or damp cloth when cleaning the plug. Remove any foreign matter from the power plug pins. · There is a risk of burning and fire. If you wish to move the freezer/refrigerator, hold it by the handles on its back and bottom . · If the appliance is disconnected from the power supply, you should wait for at least five minutes before plugging it back in. If the freezer/refrigerator will not be used for a long period of time, pull out the power plug. · Any deterioration in the insulation may cause fire. Do not use a wet or damp cloth when cleaning the plug. Remove any foreign matter or dust from the power plug pins. · Otherwise there is a risk of fire. · If the refrigerator is disconnected from the power supply, you should wait for at least five minutes before plugging it back. If the refrigerator is not to be used for a long period of time, pull out the power plug. · Deterioration in the insulation may cause fire. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance. Do not place the equipment directly under the sunlight. The appliance must be positioned so that the plug is accessible after installation If the power cord is damaged it must be replaced by manufacturer, a certified service agent or qualified service personnel. This appliance contains a small amount of isobutane refrigerant (R600a), a natural gas with high environmental compatibility that is, however, also combustible. When transporting and installing the appliance, care should be taken to ensure that no parts of the refrigerating circuit are damaged. Refrigerant squirting out of the pipes could ignite or cause an eye injury. If a leak is detected, avoid any naked flames or potential sources of ignition and air the room in which the appliance is standing for several minutes. · In order to avoid the creation of a flammable gas-air mixture if a leak in the refrigerating circuit occurs, the size of the room in which the appliance may be sited depends on the amount of refrigerant used. [. . . ] · Connect one end of the earthing wire (yellow/green or green) to the earth screw and the other end to a steel or copper pipe, such as a water pipe. ADJUSTING THE CLEARANCE BETWEEN THE DOORS Adjusting the small step difference between doors. If the door of freezer is lower than that of the refrigerator. If the door of freezer is higher than that of the refrigerator. Adjustment part Adjustment part Please open the doors and adjust the doors as follows: 1) Release the nut (x) on the lower hinge until the upper end of the bolt (). When you release the nut(x), use enclosed hex wrench () to turn the bolt() a little counterNOTE clockwise to make the nut(x) loose with your fingers. WRENCH WRENCH NUT BOLT NUT BOLT 2) Please adjust the height difference between the doors turning the bolt () turn clockwise( clockwise ( ). When you turn clockwise ( NOTE WRENCH ) or counter ), the door goes up. WRENCH BOLT BOLT 3) After adjusting the doors, turn the nut (x) turn clockwise( en the bolt again with wrench () to fix the nut(x). WRENCH ) until the lower end of the bolt, then tight WRENCH NUT BOLT NUT BOLT If you do not fix the nut (x)firmly, the bolt () may be released. [. . . ]