User manual SAMSUNG S19A10N

[. . . ] SyncMaster S19A10N Monitor User Manual The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Table Of Contents MAJOR SAFETY PRECAUTIONS Before You Start . 1-4 INSTALLING THE PRODUCT Package Contents . 2-4 USING THE PRODUCT Standard Signal Mode Table . 3-3 TROUBLESHOOTING Monitor Self-Diagnosis . [. . . ] · Otherwise, it may result in a problem with the product or injury. · Maintaining the Correct Posture when Using this Product Maintain the correct posture when using this product. · · · · · · Straighten your back. Keep a distance of 45~50 cm from your eyes to the screen. Look down at the screen and face the screen forwards. Adjust the angle of the product so that light is not reflected onto the screen. Keep your elbow at a right angle and keep your arm level with the back of your hand. Place your heels flat on the ground while keeping your knees at an angle of 90 degrees or higher and maintain the position of your arm so that your arm is below your heart. 1-4 Major Safety Precautions 2 2-1 · · Installing the Product Package Contents Unpack the product and check if all of the following contents have been included. Store the packaging box in case you need to move the Product at a later stage. Monitor Contents Installation Manual Product Warranty (Not available in all locations) D-Sub Cable Stand Connector Stand Power Cord Installing the Product 2-1 2-2 Installing the Stand Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. Insert the Stand Connector into the Stand in the direction shown by the figure. Check if the Stand Connector is firmly connected. Turn the connecting screw at the bottom of the stand fully so that it is completely fixed. Place a soft cloth over the table to protect the product and place the product onto the cloth so that the front of the product is facing downwards. 2-2 Installing the Product Hold the main body of the product with your hand as shown by the figure. Push the assembled stand into the main body in the direction of the arrow as shown in the figure. - Caution Avoid lifting the product holding only the stand. Disassembly is in the reverse order of the assembly. Installing the Product 2-2 2-3 Connecting with a PC The connecting part may differ depending on the product model. 1. Connect the product to a PC depending on the video output supported by the PC. · · When the graphics card provides D-Sub Analog output Connect the [RGB IN] port of the product to the [D-Sub] port of the PC with the D-Sub cable. 2. To use the product, connect the power cable to a power outlet and the [POWER] port on the product. (The input voltage is switched automatically. ) When the product is connected to a PC, you can turn the product on and use it. Cables can be fixed as shown. 2-3 Installing the Product 2-4 Kensington Lock A Kensington Lock is an anti-theft device that enables users to lock the product so that they can safely use it in public locations. Since the shape and usage of the locking device may differ depending on the model and the manufacturer, for more information, refer to the User Manual supplied with the locking device for more information. You must purchase the Kensington Lock separately. To lock the product, follow these steps: 1. Wrap the Kensington lock cable around a large, stationary object such as a desk or chair. Slide the end of the cable with the lock attached through the looped end of the Kensington lock cable. Insert the locking device into the Kensington slot on the Monitor( 4. For exact instructions, see the User Manual supplied with the locking device. You can purchase the locking device from an electronics store, an online shop, or our service center. Installing the Product 2-4 3 3-1 Using the product Standard Signal Mode Table This product delivers the best picture quality when viewed under the optimal resolution setting. The optimal resolution is dependent on the screen size. [. . . ] Windows 7 : Change the resolution by selecting Control Panel Appearance and Personalization Display Adjust resolution. (For more information, refer to the User Manual of the computer or the graphics card. ) Windows XP : Configure it by selecting Control Panel Appearance and Themes Display Screen Saver Setting or configure it in the BIOS Setup of the computer. Windows ME/2000 : Configure it by selecting Control Panel Display Screen Saver Setting or Configure it in the BIOS Setup of the computer. Windows Vista : Change settings by selecting Control Panel Appearance and Personalization Personalization Screen Saver. [. . . ]