User manual SAMSUNG SADT-100CM

[. . . ] The SAMSUNG logo is a registered trademark of Samsung Electronics. Microsoft and Windows are registered trademarks of Microsoft Corporation. VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association.  An administration fee may be charged if either  (a) an engineer is called out at your request and there is no defect in the product (i. e. where you have failed to read this user manual).  (b) you bring the unit to a repair centre and there is no defect in the product (i. e. [. . . ] A user can also change the EWF configuration by entering EWF management commands at the command prompt. This task requires the Administrator privilege.  Enable write filter and restart the system. If this item is selected, the cache is flushed and the EWF is enabled. After restarting your computer, the configurations and file system information for the client are written to a cache. You can also perform this operation by entering “ewfmgr. exe c: -enable” at the command prompt and restarting your computer.  Disable write filter and restart the systems. This item is activated when the EWF is running. If this item is selected, the current states of the client (saved in a cache) are saved to a flash volume and the EWF is disabled. After restarting your computer, the configurations and file system information for the client are written to a flash volume. 2 Using "Windows Embedded Standard 7" (TB-WH) 34 2  Using "Windows Embedded Standard 7" (TBWH) You can also perform this operation by entering “ewfmgr. exe c: -commitanddisable” at the command prompt and restarting your computer. This item is activated when the EWF is running. If this item is selected, the current states of the client (saved in a cache) are saved to a flash volume. However, the state of EWF will not be changed. Therefore, it is better to save files to the server rather than to your client. Mapping a Network Drive The Administrator can map a folder to a network drive. To keep the mapping information after restarting the client, take note of these directions carefully.  Select the Reconnect at logon checkbox in the Map Network Drive dialog box. If the EWF or FBWF is enabled, you must disable it before proceeding with installation.  2 Using "Windows Embedded Standard 7" (TB-WH) 36 2 Using "Windows Embedded Standard 7" (TBWH) 2. 3. 5 Recover the System Overview The WES Client provides a recovery function which allows you to revert to a backed up system when encountering a serious problem. You can back up an OS image which is working normally to USB memory or the PXE server. You can revert to a backed up image when your client has one of these problems:  When a system file is deleted accidentally or is corrupted When the client computer is unstable or there is a problem with a device driver When problems occur, after installing a new program or device When the client computer is infected with a virus When Windows Embedded Standard fails to start When a system file is deleted accidentally or is corrupted     How to Recover the System  Recovery Using USB Memory By following these steps, you can save all necessary files to USB memory, and boot up with the backed up system on the USB memory and recover the system. 1 2 3 4  Perform system formatting for your USB memory in order to make it bootable. Save the Windows Embedded Standard image and the Backup/Recovery Utility which will be recovered later to your USB memory. Recover the system using the Windows Embedded Standard image and the Backup/ Recovery Utility in the USB memory. Recovery Using Network Booting This method is provided through the PXE (Preboot eXecution Environment) server. The PXE sever provides a client/server interface based on TCP/IP, DHCP, and TFTP. It allows an administrator at a remote location to configure and boot the operating system onto a client over a network.  Implement a PXE server. Save the Windows Embedded Standard image and the Backup/Recovery Utility which will be recovered later onto the PXE server. Recover the system using the Windows Embedded Standard image and the Backup/Recovery Utility saved on the PXE server via the network. For more information, refer to the PXE Server User Manual.    2 Using "Windows Embedded Standard 7" (TB-WH) 37 2 2. 4 Using "Windows Embedded Standard 7" (TBWH) MagicRMS Pro 2. 4. 1 About MagicRMS Pro The MagicRMS Pro program can be used to remotely control a Samsung network monitor. [. . . ] You can connect to more than one desktop or application. The names of the desktops and applications connected will be highlighted. 2 Disconnect The Disconnect button disconnects the corresponding desktop or application connected. When the desktop or application is disconnected, a list of connected desktops or applications will appear if there are any. 3 Refresh To update the Desktop List that contains a list of desktops or applications on the Citrix Server, click Refresh. 3 Using the "Zero Client" (TB-CH) 66 3 4 Using the "Zero Client" (TB-CH) Reconnect You can display desktops and applications that are not displayed even though they are connected to the Client. Double-click the desktop or application desired. [. . . ]