User manual SAMSUNG SC-4147

[. . . ] · Do not handle vacuum cleaner or plug with wet hands. · Do not put any object into openings. Do not use with any opening blocked; keep openings free of dust, lint, hair and anything that may reduce air flow. · Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts. [. . . ] · Keep suction away from your face when using nozzles and pipe. · Do not pull the power cord around sharp corners and do not allow it to become trapped. · Unplug before connecting turbine nozzle. (only using turbine-brush model) SAVE THESE INSTRUCTIONS FOR FUTURE USE. 1 Assembling Parts Assembled Vacuum Cleaner Parts 1-1 The assembled cleaner will look like the illustration to the left. 1. Handle 2. Power switch 3. Quick release cord hook 4. Post-Motor Filter 5. Crevice tool 6. Handle release 7. Carrying handle 8. Hose 9. Extension wand 10. Combination tool 11. Cyclone-Lever 12. Dirt Cup 13. Filter Cup 14. Upper Tank 15. Louvers 16. Hose Wand Base 17. Height Adjustment Dial 18. Hose Clip Front Back WARNING! OPERATE THE VACUUM CLEANER ONLY AT THE VOLTAGE SPECIFIED ON THE NAMEPLATE. Step 1. Attaching the Handle 1-2 Stand the vacuum upright and slide the base of the handle firmly into the grooves at the top of the vacuum body. 1-3 Insert the screw provided into the existing hole. Tighten the screw securely with a screwdriver. Before securing the handle, please check that the handle is fitted to the vacuum body and make sure there's no gap. Step 1. Attaching the Handle 1-4 Slide the end of the hose wand with tabs into the Hose Wand Base. 1-5 Slide the extension wand and the crevice tool together into the storage clip. 2 Operation 2-1 2-2 2-3 ON-OFF Switch 1. To turn cleaner on, press the Power switch. 2. To the cleaner off, press the Power switch again Handle positions The handle of your cleaner has three positions; upright for storage and when using cleaning tools; operating for general operation on carpet and floors; low for reaching under low furniture. Step on handle release pedal to lower handle. Transporting cleaner To move your cleaner from room to room, put the handle in upright position, tilt the cleaner back on its rear wheels and push forward. 2-4 2-5 A B C ·option Carrying handle The cleaner can also be moved by using the carrying handle. 2-6 Cleaning Tool attachments Attachment tools can be used to clean furniture or drapes, on stairs or in corners. When using the attachments, ensure the vacuum cleaner is placed firmly on the floor with the handle in the upright position. Do not place the vacuum on top of furniture or steps as the brushroller may cause damage. Replace the door by inserting the tabs on the left side and snapping the right side into place. Do not operate cleaner without Either the Pre-Motor Filter or Post-Motor Filter in place. Grasp the Circular Filters and twist to unlock Pull straight up to remove. Separate the Outer foam and Inner pleated Circular Filters. Wash each individually by hand in warm water. Rinse well, then air dry Thoroughly dry before putting them back together and replacing in the Filter Cup The Filter Cup may be washed In warm water with a mild detergent. Make sure it is completely dry before reassembling with fliters. 4 Maintenance The belt The belt on your cleaner causes the agitator to rotate and is important for the effective operation of the cleaner. The belt is located under the bottom plate of the cleaner and should be checked from time to time to be sure it is in good condition. 3-7 3-8 When to replace Disconnect cleaner from electrical outlet. To check belt, remove bottom plate as shown in "How to replace. " Replace belt if it is stretched, cut or broken. How to replace Disconnect cleaner from electrical outlet. Place handle in low position and turn cleaner over so bottom side is up. Remove the 4 screws as shown with a screw driver. Remove agitator and used belt. Discard used belt. 3-9 3-10 3-11 With lettering on outside of belt and positioned as shown in box on (D), slide new belt over motor pulley (B). Insert agitator through belt and place belt in belt guide (C) on agitator. [. . . ] If you notice a change in the sound of the vacuum motor, check for blockages. 3-14 3-15 3-16 Remove Dirt Cup and check Upper Tank and Louvers. Check to make sure Louvers are Installed correctly. To unlock the Louvers, grasp the rim and turn Toward the left. If the Louvers are missing or not locked into place, check and clear the tube in the center of the Dirt Cup. Remove the Hose and disconnect the Wand. [. . . ]