User manual SAMSUNG SCC-100AP INTRODUCTION

[. . . ] This appliance should not be place in a built-in installation such as a bookcase, unless proper ventilation is provided. This appliance should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. Do not allow anything to rest on the power cord. [. . . ] When the appliance exhibits a distinct change in performance this indicates a need for service. E 14. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. Upon completion of any service or repairs to the appliance, ask the service technician to perform routine safety checks to determine that the appliance is in safe operating condition. iv v User Guide User Guide Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Precautions in Installation and Use . . . . . . . . . . . . . . . . . . . . 5 Connecting Auto Iris Lens Connector. . . . . . . . . . . . . . . . . . . . . 6 Mounting Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Setting Lens Selection Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . First, following is how to adjust the Back Focus of the Fixed Focus Lens. E Lightly loosen the screw fixing the Back Focus Adjustment Ring using a screwdriver. Image a vivid subject (with check patterns) at a distance of more than 10m away and turn the Focus Ring to the infinity ( ) position. Adjust the Back Focus Adjustment Ring to obtain the clearest image of the subject. Fasten the screw fixing the Back Focus Adjustment Ring. 8 9 User Guide User Guide The following describes how to adjust the Back Focus when using a Zoom lens. Lightly loosen the screw fixing the Back Focus Adjustment Ring using a screwdriver. Image a vivid subject (with check patterns) at a distance of 3~5m away and adjust the zoom of the lens to TELE as far as it goes. Then adjust the Focus Ring of the lens to obtain the clearest image of the subject. Adjust the zoom of the lens to WIDE as far as it goes. Then turn the Back Focus Ring of the camera to obtain the clearest image of the subject. & 2~3 times to exactly coincide the zoom focus from TELE and with that from WIDE. Fasten the screw fixing the Back Focus Adjustment Ring. Connecting Cable After mounting the lens and setting the Lens Selection Switch, connect the prepared cable to each terminal of the camera. [. . . ] To switch the screen gently without a jump, set the camera to LL and adjust the Vertical Sync Phase using the INC/DEC switch. 1. FL ON 3) SW3 (FL): This is to prevent flicker on the screen when NTSC system is used in 50HZ power supply region and PAL system is used in 60HZ power supply region. That is to prevent shaking on the screen resulted from the discordance of the vertical sync frequency and the flicker frequency of the illumination. While this switch is ON, the electronic shutter is fixed to 1/100sec (NTSC) or 1/120 sec (PAL). [. . . ]