User manual SAMSUNG SCQ-041AP

[. . . ] SCQ-041P User's Guide ALAR SYST FREE DI QUAD LE SING AUTO SWIT CHER DISP LAY SPLA Y ZE EM SE TUP M RESET SETUP LIST 1 12 34 ACTER CHAR 2 ENTER 1 3 2 4 3 SELECT 4 MENU POW ON ER HE L DIGITA QUAD SWITC R COLO R P -041 SCQ OFF DIGITAL COLOR QUAD SWITCHER Part No. : AB68-00052A Printed in Korea SAFETY PRECAUTIONS WARNING: To Reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. iii User's Guide IMPORTANT SAFEGUARDS 1. Read instructions: All the safety and operating instructions should be read before the appliance is operated. Retain instructions: The safety and operating instructions should be retained for future reference. Heed warnings: All warnings on the appliance and in the operating instructions should be adhered to. [. . . ] The SCQ-041P requires the following operating conditions to maintain temperature and humidity. · Operating temperature : 32 - 86°F (0 - 40°C) · Relative humidity : 30% - 90% relative humidity · Input voltage : AC 100V-240V · Power of consumption : 10 Watts · Frequency : 50 Hz/60 Hz CAUTION Please supply input power voltage with a variation of less than 10% of the specific voltage to the system in use. Please do not connect other appliances or equipment using the system's power outlet. It is recommended to use AVR to supply a stable power source. If you would use this appliance to supply voltage for 240V, you should be used the proper plug adapter for 240V rating. 8 Chapter 2 Unpacking Upon receipt of the SCQ-041P system, unpack the box and put the unit on a floor stand, or the place the unit where you are going to install the system. Please check the contents of the package as listed below: · SCQ-041P MAIN UNIT · USER'S GUIDE · POWER CABLE (1 EA) · 19-inch RACK MOUNT ADAPTOR (2 EA) POWER ON AUTO SWITCHER DIGITAL COLOR QUAD SWITCHER SINGLE DISPLAY QUAD DISPLAY FREEZE SYSTEM SETUP SETUP ALARM RESET 1 3 2 4 12 34 1 3 SELECT 2 CHARACTER OFF SCQ-041P 4 MENU ENTER LIST 9 User's Guide Mounting the SCQ-041P in a Rack The is a standard 19-inch electronic equipment rack. If you intend to mount the SCQ-041P in a rack, do as following: 1. Remove the mounting screws from their holes and align each Rack mounting adaptor vertically along the front edge of the SCQ-041P enclosure. Insert the mounting screws through each mounting adaptor and into the corresponding screw holes on the SCQ-041P. Partially tighten the screws so that they are holding the adaptor loosely in place. Adjust the mounting adaptor the front of the adaptor is flush with the front panel of the SCQ-041P enclosure. Tighten the mounting screws so that the adaptor is firmly attached to the SCQ-041P enclosure. Be careful not to over tighten the screws. Repeat the procedure described above to attach the remaining adaptor to the other end of the SCQ-041P enclosure. POW ON ER OFF DIGITA COLO L R QU SCQ AD SWITCHE -041 R AUTO SWIT CHER SING LE DI SPLA Y QUAD DISP LAY FREE ZE SYST EM SE TUP ALAR SETUP MENU ENTER LIST P 1 3 2 4 12 34 1 3 SELECT CHARA 2 CTER M RESET 4 10 Chapter 2 After you have attached both mounting adaptor to the SCQ-041P, align the SCQ-041P within the appropriate space in the rack and attach it firmly to the rack. Warning Install the SCQ-041P on the Rack with a minimum distance between the SCQ-041P and the other system of at least 22mm(a half of the SCQ-041P height) 11 User's Guide Chapter 3, Connecting Other Components You can connect a monitor, a camera, a VCR, a PC, and the other external components to the SCQ-041P. This chapter describes how to connect these components. CAUTION Please do not supply over 2V DC to the "VIDEO INPUT-CH1", "VIDEO INPUT-CH2", "VIDEO INPUT-CH3", or "VIDEO INPUT-CH4" input terminals. Connecting a Camera VIDEO INPUT CH1 CH2 CH3 CH4 VIDEO OUTPUT IN OUT IN OUT IN OUT IN OUT 1 2 Camera 1 Camera 2 Camera 3 Camera 4 12 Chapter 3 Connecting a VCR VIDEO INPUT CH1 CH2 CH3 CH4 VIDEO OUTPUT IN OUT IN OUT IN OUT IN OUT 1 2 VIDEO INPUT VIDEO INPUT CAUTION Connect monitor and VCR separately to both of " VIDEO OUTPUT" connectors. 13 User's Guide Connecting a Monitor Camera VIDEO INPUT CH1 CH2 CH3 CH4 VIDEO OUTPUT IN OUT IN OUT IN OUT IN OUT 1 2 123 4 Monitor 1 (Quarter screen display mode) Monitor 2 (Auto switching display mode) If you connect a monitor to the VIDEO OUTPUT terminal with the " " mark, it is configured as a quarter screen display. If you connect a monitor to the VIDEO OUTPUT terminal with the " " mark, it is configured as a quarter-section screen, single screen or an automatic sequence screen. This feature allows the unit to switch a single screen from four channels in sequence. But when the channel VIDEO LOSS happened or is set to interval time of "AUTO SWITCHER SET" as "0", It is skipped. CHANNEL LOSS or it is set to interval time of all channels as "0" of "AUTO SWITCHER SET", it is converted quad screen. 14 Chapter 3 Connecting an Alarm ALARM IN/OUT ALARM INPUT CH1 2 3 4 ALARM OUT OUT GND RS - 232C ~ AC IN GND 1 2 3 4 RESET Time Lapse VCR Alarm unit Sensor Connecting External Components Monitor 1 (Quarter screen display mode) 123 4 Monitor 2 (Quarter screen, Auto switching or single screen display mode) Camera CH1 CH2 VIDEO INPUT CH3 CH4 VIDEO OUTPUT IN OUT IN OUT IN OUT IN OUT 1 2 External Components 15 User's Guide Chapter 4, Configuring the SCQ-041P In accordance with the above procedure, you can proceed to configure system operation once you finish connecting the other components to the SCQ-041P. To proceed with system configuration, you must access the system setup mode to use the setup menu. The system setup procedure is as follows. [. . . ] When the alarm is disabled, the alarm output becomes TTL "HIGH" level. When the alarm is disabled, the alarm reset output is maintained for 150ms and then becomes TTL "HIGH" level. The date, hour, and channel number of the relevant alarms are recorded in the alarm list. NOTE Press the "LIST" button to scan this information. 11. [. . . ]