User manual SAMSUNG SCX-5312F

[. . . ] SCX-5312F/5112 User's Guide Home Visit us at: www. samsungelectronics. com/mfp P/N: JC68-00851A Rev. 2. 00 CONTENTS Chapter 1: GETTING STARTED 1. 2 1. 4 1. 4 1. 5 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Component Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The printed side should be facing down and the edge without curl at the right side. If you experience problems feeding paper, turn the paper around. Note that the print quality is not guaranteed. PAPER HANDLING 3. 5 Using the Bypass Tray The Bypass tray is located at the right side of your product. It can be closed when you are not using it, making the product more compact. Use the bypass tray to print transparencies, labels, envelopes or postcards in addition to making quick runs of paper types or sizes that are not currently loaded in the paper cassette. Acceptable print media are plain paper with sizes ranging from 3. 9x5. 8, to Legal 8. 5 x 14 inch, the largest size acceptable, and weighing between 16lb and 32lb. The following table summarizes the print media allowed as well as their stacking height limit. Paper Type Stacking Height Limit Plain Paper Envelope Transparency Label Cardstock 100 sheets or 9mm (max)a 10 envelopes or 9mm (max)a 30 sheets or 9mm (max)a 30 sheets or 9mm (max)a 10 sheets or 9mm (max)a a. The height is measured with the stack of sheets laid, without being touched by hands, on a flat surface. Notes: · Always load only the print media specified in Specifications to avoid paper jams and print quality problems. · Do not hit the bypass tray or rest your hands on it; otherwise the tray may be damaged or detached from the product. · Remove any curl on postcards, envelopes, and labels before loading them into the multi-sheet bypass feeder. 3. 6 PAPER HANDLING To load print media in the Bypass tray: 1 Lower the Bypass tray, located on the right side of the product. Unfold the paper support extension as shown. Paper support 3 Bypass tray 2 Prepare a stack of paper or envelope for loading by flexing or fanning them back and forth. Straighten the edges on a level surface. For transparencies; hold the transparencies by the edges and avoid touching the print side. Oils from your fingers that are deposited on the transparency can cause print quality problems. If you are using the transparencies with paper backing, insert a sheet of plaing paper on the tray before loading transparencies. Doing so prevents paper jams while feeding. 3 Load the print material with the print side facing down and against the right edge of the tray. PAPER HANDLING 3. 7 4 Adjust the paper guide to the width of the stack of print material. Make sure that you have not loaded too much print media. The print media buckles if you load a stack that is too deep, or push it in too far. Max. fill line NOTES: When printing on the used paper from the bypass tray, the printed side should be facing up and the edge without curl at the left side. If you experience problems feeding paper, turn the paper around. 3. 8 PAPER HANDLING Setting the Paper Size for Copying After loading paper in the paper cassette or the bypass tray, you have to set the correct paper size using the control panel buttons. These settings will apply to the Copy mode, and the Fax mode (SCX-5312F only). In PC printing mode, you have to select the paper size in the application program you use. To set the paper size for cassette, take the following steps: 3 1 Press Menu/Exit and then System Data from the onetouch dial keypad. SCX-5112 users should press Menu and then Enter. [. . . ] Check if the display shows "MEMORY FULL". Your product cannot receive faxes manually. Did you hang up the handset of the external telephone before you start faxing?Make sure that the document is loaded face down. [. . . ]