User manual SAMSUNG SD-9420

[. . . ] Four-pin sound output terminal for use with a sound card (refer to the sound card documentation for further details) 3. Forty-pin host IDE interface connector 5. Four-pin power terminal 3 Remove the cover from a free expansion slot and install the DVD-ROM drive, as shown in the illustration. q If you have no free expansion slot, install the drive in place of the diskette drive. DVD-ROM drive 2 3 Connecting the Cables Setting Up the Device Driver 1. Audio cable x Automatic Setup 1 Insert the setup diskette in the diskette drive and change the directory to A:, where A: is the diskette drive. [. . . ] 3 Reboot the computer. x 2 Installing a jumper on the master/slave select terminal Install the jumper in the correct position on the terminal: MA to use the device in the master mode SL to use the device in the slave mode CS to control the device via a CSEL host interface signal See Step 3 for further details. Manual Setup 1 Make the C:\SAMSUNG directory. 2 Copy the files from the diskette to the C:\SAMSUNG directory. To do so, type COPY A:*. * C:\SAMSUNG after the C:\ prompt and press [Enter]. 3 Connecting the IDE cable Two configurations are possible. q The DVD-ROM drive is the only IDE device in addition to the hard disk. Install the jumper in the SL position (Slave). Connect the 40-pin flat IDE cable from the IDE port on the mother board, first to the DVD-ROM drive and then to the hard disk. Hard disk (MA) 3 Edit the CONFIG. SYS file. Add the DEVICE=C:\SAMSUNG\SSCDROM. SYS \D:SSCD000 /V entry. LAST DRIVE = Z ----------------------------------------------------------------------DEVICE = C :\SAMSUNG\SSCDROM. SYS /D : SSCD000 /V IDE port Mother board DVD-ROM (SL) q You already have an additional IDE device installed in your computer. First IDE cable 4 Edit the AUTOEXEC. BAT file. Add the C:\SAMSUNG\MSCDEX /D:SSCD000 entry. ----------------------------------------------------------------------C :\SAMSUNG\MSCDEX /D:SSCD000 Second IDE cable Mother board DVD-ROM (MA) CD-ROM (SL) Hard disk (SL) Hard disk (MA) Install the jumper in the MA position (Master). Connect the 40-pin flat IDE cable from a second IDE port on the mother board directly to the DVD-ROM drive or first to another additional IDE drive and then to the DVD-ROM drive. 5 Reboot the computer. 4 Connecting the audio cable from a sound card Connect the 4-pin audio cable between the sound output terminal on the DVDROM drive and the audio input terminal on the sound card. 4 5 Installing the Device Driver No additional device driver is needed for Windows 95/98/NT, as the default Windows device driver is used. You can check that the DVD-ROM drive has been correctly detected by Windows. To do so, proceed as follows. Using the DVD-ROM Drive To play audio or video CDs in your DVD-ROM drive, proceed as follows. 1 Double-click on the My Computer icon on your desktop. 2 Double-click on the Control Panel folder. 5 Expand the CD-ROM branch. The SAMSUNG DVD-ROM SD - 1 Push the power button and boot the computer. 2 After booting the computer, open the disc compartment by pressing the Eject button. 3 Insert the disc (CD/DVD) with the label on the disc facing upwards and close the disc compartment by pressing the Eject button. x Check the position of the jumper in the master/slave select terminal. x Reinstall the device driver or update it with the latest version by downloading it from the Samsung Web site. x This case may occur when there is a Windows installation problem; reinstall Windows. x Check whether the audio cable is correctly connected to the sound output terminal on the DVD-ROM drive and the sound card CD-IN terminal. x Check that the sound card is operational. x Install the latest version of the device driver. x Check whether the CD is of good quality and clean it, if necessary. x Check that the power cable is correctly connected. Insert a pin or unfolded paper clip in the emergency hole and push firmly until the disc compartment opens. ITEM SD - 610 SD - 612 DVD / CD DVD-ROM, DVD-VIDEO, CD-DA(Audio), CD-ROM, DISC Disc types supported Disc diameter CD-ROM XA, CD-Plus, CD-Extra, Photo-CD(Single, Multi-session), Video CD ready, Enhanced CD, CD-I/FMV, CD-R, CD-RW 12cm or 8cm Sustained : Max. 6, 000KB/sec (40X) Data transfer rate Sustained : Max. [. . . ] 6, 000KB/sec (40X) Data transfer rate Sustained : Max. 6, 000KB/sec (40X) The DVD-ROM drive is not recognized by MS-DOS. The DVD-ROM drive is not detected by Windows. No sound is heard from an audio CD. PIO Mode 4 : 16. 6MB/sec Multiword DMA mode 2 : 16. 6MB/sec UDMA mode 2 : 33MB/sec Access time(1/3stroke) 130ms / 110ms(Typical) DRIVE PERFORMANCE Data buffer capacity 512KB Laser Slide mechanism Spindle motor ERROR RATE Eject button FRONT PANEL Indicator(LED) Headphone output Volume control Required power REAR PANEL Interface connector Audio output Jumper block Operation OPERATING ENVIRONMENT Storage GENERAL RELIABILITY Dimensions Net weight MTBF BUSY Stereo mini-jack(Ø3. 6mm) 0. 60±20%(rms) 33 Wheel knob +5VDC : 2. 0A, +12VDC : 1. 0A (Max) ATAPI Line out 0. 70 ± 20%(rms) : 47K Device configuration jumper Temperature : 5 ~ 45°C, Temperature : -40 ~ 60°C, 149(W) x 42(H) x 200(D)mm 880g 125, 000 POH(Duty 20%) Humidity : 8 ~ 80% Humidity : 5 ~ 90% Semiconductor Laser Stepping motor Brushless motor 10-15 / MODE1:10-12, MODE2:10-9 Auto eject or Auto inject A CD is not read or is read too slowly. [. . . ]