User manual SAMSUNG SDB-100

[. . . ] Retain instructions: The safety and operating instructions should be retained for future reference. Heed warnings: All warnings on the appliance and in the operating instructions should be adhered to. Follow instructions: All operating and use instructions should be followed. Cleaning: Unplug this video product from the wall outlet before cleaning. [. . . ] In this case the SET LED turns on and the BORDER LINE on the left upper of screen blinks. 2) Move the section whose border blinks to a desired position using the move button. 3) Press the "CAMERA SELECT" button equivalent to the desired channel at the position. 4) Repeat operation in 2), 3) until setting is completed. 5) Press the "SET" button after completing setting. The previously indicated division indication mode is returned if selecting the division screen using the "MULTI SCREEN" button on the full screen. "MULTI SCREEN" button does not operate in the following cases: - In setting division screen - In setting of program mode - In displaying ALARM/LOSS LIST on screen - During zoom operation 4-2 Digital Multiplexer When desiring to see automatic sequential conversion screen The automatic sequential conversion mode operates in the LIVE screen status and consists of the following 2 cases: The FULL screen is converted if pressing the "SEQUENCE" button in the FULL screen status. The screen on the bottom right side is converted if pressing the "SEQUENCE" button in the 4, 9-division screen status. The LED of the "SEQUENCE" button turns on for both cases. The conversion time in the automatic sequential conversion mode is set in the "SEQUENCE. . " of the "2. MON OUT SET" in case of the PRPGRAM mode for the FULL screen and the time to set up is 00sec ~ 30sec. The screen on the right bottom is switched in the interval of a second for the 4, 9-division screen. ENGLISH Method to release - Press the "SEQUENCE" button once again. And then it stops on the screen currently seen. The "SEQUENCE" button does not operate in the following cases: In replay mode or TRIPLEX mode In the division screen mode other than 4, 9-division screen In setting of program mode In displaying ALARM/LOSS LIST on screen During ZOOM operation During ALARM operation 4-3 Digital Multiplexer When desiring to see the stop screen The monitor screen (full screen and division) may be seen with a temporary stop. Record setting of each camera You can set record mode and record duty, ON/OFF, reservation of each channel. The following screen is displayed on screen if pressing the "ENTER" button after placing the blinking indication on the "1. REC OUT SET" by pressing the "MOVE" button from the main menu. [REC OUT SET] REC TYPE REC OUT DUTY SET. . . RESERVATION TLV FIELD OFF ¡ - The blinking indication moves if pressing " ", " " button. - The setting value is changed if pressing " ", "¡ " button. - The changed setting value is stored if pressing the "SET" button. REC TYPE : NOR TLV · NOR : Used when connecting general VCR. · TLV : Used when recording in the TLV mode by connecting the time lapse VCR. - Output in the normal mode if no trigger signal exists though the setting is done in the TLV mode. REC OUT : FIELD FRAME : Effective menu if "REC TYPE" is "NOR". [. . . ] · Set the "REC TYPE" to "NOR" in the "5. ALARM SET" of the "program mode". The record output until release after the alarm occurs is as follows: VCR TRIG TRIG override Record output operation ALARM/MOTION OUT Output ALARM RESET Output TLV operation NOR operation TLV More than 150ms Alarm occurrence Alarm reset 7-1 Digital Multiplexer 5. Alarm/Loss list reference If pressing the "LIST" button on the front, alarm, channel loss and motion detection information recently occurred is output up to 100EA (10EA x 10 page) on screen in the occurrence as follows: Current page/ whole page ENGLISH [ALARM/LOSS LIST] 1/3 YY/MM/DD HH:MM:SS CH 1. 00/ 01/ 23 12: 30: 30 A 11 RIGHT LEFT [ALARM/LOSS LIST] 2/3 YY/MM/DD HH:MM:SS CH 11. [. . . ]