User manual SAMSUNG SDM-160MP INTRODUCTION

[. . . ] SDM-160/SDM-160P/SDM-160M/SDM-160MP USER'S MANUAL DIGITALMULTIPLEXER Digital Multiplexer CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Graphic Symbol Explanation The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Warning-To Prevent Fire or Shock Hazard, Do Not Expose This Equipment To Rain or Moisture. IMPORTANT SAFEGUARDS 1. Read instructions: All the safety and operating instructions should be read before the appliance is operated. [. . . ] The LED turns off and the stop mode is released if pressing the "FREEZE" button once again. 2. FREEZE setting of division screen The LED blinks if pressing the "FREEZE" button. The selected screen stops if selecting a channel to freeze, and "F" character is displayed. The selected channel is released if pressing the relevant channel again and stop of all channels if pressing the "FREEZE" button. 01/05/01 12:30:26 01/05/01 12:30:26 F CH1 CH2 Flash FREEZE CH1 F CH3 CH4 FULL screen 4-division screen The "FREEZE" button does not operate in the following cases: - In setting division screen mode - In setting of program mode - In displaying ALARM/LOSS LIST on screen When desiring to see in the zoom screen The zoom screen operates if pressing "ZOOM" button in the FULL mode. The mode is changed in the following order whenever pressing this button. FULL MODE © 2TIMES ZOOM © 4 TIMES ZOOM © FULL MODE Select the area to expand using the "MOVE" ( , , , ¡ ) button. Moving to the diagonal direction is allowed using the double button (right upper, left below, right upper, right below). The "ZOOM" button does not operate in the following cases: - In division screen mode - In setting division screen - In setting of program mode - In displaying ALARM/LOSS LIST on screen 4-4 ¡ ¡ ¡ Digital Multiplexer When desiring to see in the PIP screen The PIP (picture in picture) screen may be seen using the "PIP" button on the FULL screen in the LIVE mode. The size of the PIP sub-screen is set in the "PIP SIZE" of the "2. The sub-screen is automatically and sequentially converted if pressing the "SEQUENCE" button. ENGLISH Method to use 1. In this case the LED of the "SET" button blinks and the border line blinks. Then, set the sub-screen of the PIP screen to a desired channel. Press the "SET" button if completing the channel setting. In this case the LED of the "SET" button turns off. Fix the position of the sub-screen using the "MOVE" button. The position of the sub-screen may be selected in 4 cases of right upper, left below, right upper, right below. The "PIP" button does not operate in the following cases: - In replay mode or TRIPLEX mode - In division screen - In automatic sequential conversion mode - In zoom operation - In setting program mode - In displaying ALARM/LOSS LIST on screen When desiring to see in the record screen You can see the record output screen in the live mode using the "REC CHECK". When desiring to see output of VCR as it is You can see the output screen of VCR using the "REC CHECK" button in the replay mode. This mode is useful when adjusting MENU of VCR. The "REC CHECK " button does not operate in the following cases: - In zoom operation - In setting program mode - In displaying ALARM/LOSS LIST on screen 4-5 Digital Multiplexer Chapter 5. Setting of Program Menu <MAIN MENU> The following main menu is displayed on the monitor screen if pressing "MENU" button, the "MENU" LED turns on. The LED turns off if pressing the button and it returns to the previous status. REC OUT SET MON OUT SET CHANNEL TITLE SET DATE / TIME SET ALARM SET MOTION SET SYSTEM SET < SUB MENU> - Select item 1~7 of the main menu using the "MOVE" button ( - Press the "ENTER" button to move to the sub-menu. ¡ , ¡ ). 1. Record setting of each camera You can set record mode and record duty, ON/OFF, reservation of each channel. The following screen is displayed on screen if pressing the "ENTER" button after placing the blinking indication on the "1. [. . . ] 00/ 01/ 23 12: 30: 30 A 11 RIGHT LEFT [ALARM/LOSS LIST] 3/3 YY/MM/DD HH:MM:SS CH 21. 00/ 01/ 23 12: 30: 30 A 11 Position is changed depending on the date display type. ALARM : "A" LOSS : "L" MOTION : "M" - Page moves if pressing " ", " ¡ " button. - Update is performed if loss occurs and motion is detected in the status that list is displayed. - The list screen disappear and alarm operation is performed in the status that list is displayed. [. . . ]