User manual SAMSUNG SEF-54PZF

[. . . ] The SEF-54PZF also allows wireless P-TTL photography and high-speed sync. It is clip-on type flash which enables accurate focus adjustments even in dark locations with built-in AF-assist spot beam. Please read this manual carefully before using the flash. The optional accessories can be compatible with the Pentax. 2 FOR SAFE USE OF YOUR FLASH UNIT Although we have carefully designed this flash unit for safe operation, please be sure to follow precautions given on page 4-6. WARNING CAUTION This mark indicates precautions that, if not followed, could result in serious injury to the user. [. . . ] Confirm that the SEF-54PZF and built-in flash unit are fully charged, and take the photograph. A lamp on the SEF-54PZF will blink. You cannot set the flash unit to SLAVE while the exposure metering timer is on (while information relating to aperture etc. Slide down the setting switch to the (yellow dot) to display the channel on the LCD panel. Press the channel button (CH) and select a channel from 1CH to 4CH. Slide the setting switch back up to the (white dot). When you turn the camera on and press the shutter release button halfway down, the channel is registered on the camera. In the P-TTL mode, flash output setting (1/1, 2/3, 1/2, and 1/3) and flash exposure compen sation (-3. 0 to +1. 0) are possible. The flash mode on the camera must be set to (WIRELESS), otherwise the SEF-54PZF will not fire. By changing the camera's function settings, you can set the built-in flash unit so that it is not the main flash. Refer to the operating manual for the camera to find out how. For test flash, refer to page 55. 39 When Attaching the SEF-54PZF to the Camera for Control Flash Main flash Control flash only: not used for main flash (Preparation of Flash Unit Attached to Camera) 1 40 Firstly, set the wireless mode and channel of the flash unit attached to the camera, and register them on the camera. A ttach the SEF-54PZF to the hot shoe of the camera after turning the camera off. Set the power switch of the flash unit to (WIRELESS). Press the wireless mode button (M/C/S) the number of times required to display CON TROL on the LCD panel. Slide down the setting switch to the (yellow dot) to display the channel on the LCD panel. Press the channel button (CH) and select a channel from 1CH to 4CH. Slide the setting switch back up to the (white dot). When you turn the camera on and press the shutter release button halfway down, the channel of the flash unit is registered on the camera. 2 (Preparation of Separated Flash Unit) Next, set the channel of the separated (wireless) flash unit to the same channel as the flash unit attached to the camera. Place the other SEF-54PZF in the desired position. Set the power switch of the flash unit to (WIRELESS). Press the wireless mode button (M/C/S) the number of times required to display SLAVE on the LCD panel. Slide down the setting switch to the (yellow dot) to display the channel on the LCD panel. Press the channel button (CH) and select the same channel that the flash unit attached to the camera has been set to. Slide the setting switch back up to the (white dot) The two flash units must be set to the same channel, otherwise the separated flash unit will not fire. (Photographing) 3 Confirm that both flash units are fully charged, and take the photograph. A lamp on the wireless flash unit will blink. 41 When Using Both an SEF-54PZF Attached to the Camera and a Separated Flash Unit as Main Flashes Use both flash units as main flashes (Preparation of Flash Unit Attached to Camera) 1 Firstly, set the wireless mode and channel of the flash unit attached to the camera, and register them on the camera. Attach the SEF-54PZF to the hot shoe of the camera after turning the camera off. Set the power switch of the flash unit to (WIRELESS). [. . . ] Notwithstanding this, your Samsung returned to the manufacturer will be serviced free of charge according to this procedure and warranty policy. In any case, however, shipping charges and customs clearance fees are to be borne by the sender. 67 To prove the date of your purchase when required, please keep the receipts or bills covering the purchase of your equipment for at least a year. Before sending your equipment for servicing, please make sure that you are sending it to the manufacturer's authorized representatives or their approved repair shops, unless you are sending it directly to the manufacturer. Always obtain a quotation for the service charge, and only after you accept the quoted service charge, instruct the service station to proceed with the servicing. [. . . ]