User manual SAMSUNG NP900X4C-A06

[. . . ] Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation. VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association. An administration fee may be charged if either (a) an engineer is called out at your request and there is no defect in the product (i. e, where you have failed to read this user manual). (b) you bring the unit to a repair center and there is no defect in the product (i. e, where you have failed to read this user manual). [. . . ] However, the state of EWF will not be changed. You can also perform this operation by entering "ewfmgr. exe c: -commit" at the command prompt. You can view the configurations for the protected volumes by entering "ewfmgr. exe c:" at the command prompt. File-Based Write Filter (FBWF) The File-Based Write Filter (FBWF) protects the memory of the client from being overwritten by any unauthorized user. By restricting excessive writing into the memory, the FBWF allows you to use the client for a long time. If you request I/O, the FBWF has the client perform its operations using the cache instead of the memory so that the memory can be protected. The data saved in the cache is preserved while the client operates normally. It is removed when it is restarted or exited. To save the changes, you should write the relevant file onto the disk using the commit command. If you don't know which file is changed, disable the FBWF, change it, and enable it again. You can control the FBWF using the various options of the command at a command prompt. FBWF Configuration Current FBWF status : Displays the current status of the FBWF (Enabled or Disabled). Boot command : Displays the FBWF command that will be performed at the next boot-up. Save the Windows Embedded Standard image and the Backup/Recovery Utility which will be recovered later to your USB memory. Recover the system using the Windows Embedded Standard image and the Backup/ Recovery Utility in the USB memory. Recovery Using Network Booting This method is provided through the PXE (Preboot eXecution Environment) server. The PXE sever provides a client/server interface based on TCP/IP, DHCP, and TFTP. It allows an administrator at a remote location to configure and boot the operating system onto a client over a network. Save the Windows Embedded Standard image and the Backup/Recovery Utility which will be recovered later onto the PXE server. Recover the system using the Windows Embedded Standard image and the Backup/Recovery Utility saved on the PXE server via the network. For more information, refer to the PXE Server User Manual. 2 Using "Windows Embedded Standard 7" 39 3 3. 1 Connecting and Using a Source Device Before Connecting 3. 1. 1 Pre-connection Checkpoints Before connecting a source device, read the user manual provided with it. The number and locations of ports on source devices may differ from device to device. Do not connect the power cable until all connections are completed. Connecting the power cable during connection may damage the product. Check the types of ports at the back of the product you want to connect. 3 Connecting and Using a Source Device 40 3 3. 2 Connecting and Using a Source Device Connecting and Using a PC 3. 2. 1 Connecting to a PC Select a connection method suitable for your PC. Connecting parts may differ in different products. Connection Using the D-SUB Cable (Analog Type) RGB IN AUDIO IN 1 2 3 Connect the D-SUB cable to the [RGB IN] port on the back of the product and the RGB port on the PC. Connect a sound output cable to the [AUDIO IN] port on the product and the sound output port on the PC. [. . . ] This product and its electronic accessories should not be mixed with other commercial wastes for disposal. Correct disposal of batteries in this product (Applicable in the European Union and other European countries with separate battery return systems. ) The marking on the battery, manual or packaging indicates that the battery in this product should not be disposed of with other household waste. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. The battery incorporated in this product is not user replaceable. For information on its replacement, please contact your service provider. Do not attempt to remove the battery or dispose it in a fire. [. . . ]